Addi-Data MSX-E3701-DIO Скачать руководство пользователя

Страница: 6 / 59

Contents MSX-E3701-DIO

www.addi-data.com 6

Fig. 7-10:

Delay: Mode 2 (example) .............................................................................................................36

Fig. 7-11:

Sequence mode: “Sequence measurement“ ..............................................................................36

Fig. 7-12:

“Number of sequences” (example) .............................................................................................37

Fig. 7-13:

“Number of data frames” (example) ..........................................................................................37

Fig. 7-14:

Acquisition: Division factor ..........................................................................................................38

Fig. 7-15:

Acquisition: Acquisition time .......................................................................................................38

Fig. 7-16:

Acquisition: Trigger configuration ..............................................................................................38

Fig. 7-17:

Hardware trigger with “One-Shot” (a) .......................................................................................41

Fig. 7-18:

Hardware trigger with “One-Shot” (b).......................................................................................41

Fig. 7-19:

Hardware trigger with “One-Shot” (c) .......................................................................................42

Fig. 7-20:

Hardware trigger with “One-Shot” (d).......................................................................................43

Fig. 7-21:

Hardware trigger with “Sequence” (a).......................................................................................43

Fig. 7-22:

Hardware trigger with “Sequence” (b).......................................................................................44

Fig. 7-23:

Hardware trigger with “Sequence” (c) .......................................................................................45

Fig. 7-24:

Data server frame configuration (Auto-refresh mode) .............................................................46

Fig. 7-25:

Data server frame configuration (Sequence mode)...................................................................46

Fig. 7-26:

Acquisition: Data server frame format........................................................................................47

Fig. 8-1:

MSX-E3701-DIO: Dimensions........................................................................................................49

Fig. 8-2:

MSX-E3701-DIO: View from above..............................................................................................49

Tables

Table 4-1: Pin assignment: Transducer inputs ..............................................................................................15

Table 7-1: Auto-refresh mode: Data format ................................................................................................47

Table 7-2: Sequence mode: Data format......................................................................................................48

Table 8-1: MSX-E3701-DIO: Versions.............................................................................................................50

Table 8-2: MSX-E3701-DIO: Option ...............................................................................................................50

Table 8-3: Current consumption (at 24 V) ....................................................................................................51

Содержание MSX-E3701-DIO




























































Результаты поиска

Содержание MSX-E3701-DIO

Отзывы:

Похожие инструкции для MSX-E3701-DIO

Бренды по названию

Популярные бренды

Addi-Data MSX-E3701-DIO, Техническое описание

Результаты поиска

Содержание MSX-E3701-DIO

Отзывы:

Похожие инструкции для MSX-E3701-DIO

Бренды по названию

Популярные бренды