Actelis ML600 Скачать руководство пользователя страница 24

Installing the System 

Powering Up the ML600 

 

Powering Up the ML600 

Procedure 

 

1.  Verify that all of the procedures presented in section 

ML600 Installation

 (on page 4) 

have been completed. 

2.  Turn on either the AC or DC power source. 

3.  The ML600 starts running the cooling fan, initializes the system, and indicates system 

statuses on the front panel LEDs. The duration of system initialization can take a few 
minutes, providing the following events sequence:  

 

During initial boot (about 15 seconds) all LEDs are lit for a second and then turned 
off, except for the Status LED (Red), Power LED (Green) and SFP LEDs 
(ACT/LNK), which are turned On (Green) for a several minutes, while Ethernet port 
status is not finally discovered.  

 

Status LED starts blinking green when initial boot is completed and software 
loading/initialization starts. 

 

When software loading/initialization is successfully completed, all system LEDs are 
green except for the Alarm LED which can be red for a ML600 that is with factory 
setup and not configured by dipswitches. Facility LEDs (ETH, HSL, MLP) depending 
on cable availability (plugged-in) and port configuration, can be turned On or Off. 

Note: For a description of front and rear panel LED indications, see “LED Description” in the 

ML600 User Manual

 

Power Down Procedure 

There are no special procedures for powering down the ML600 system. To power down the 
system, turn off the power source or the AC power source (if equipped with AC-DC adapter). 

Where to go next 

Do one of the following: 

For a ML600 installation using the dipswitches: 

 

If the LED indications are as described in “Front and Rear Panel LEDs” in the 

ML600 

User Manual

, then no other actions are required. 

 

Otherwise, go to Troubleshooting LED Fault Indications and then verify that the 
dipswitches are correctly set, see Dipswitch Configuration. 

For a ML600 installation using MetaASSIST View: 

20     ML600 Release 5.0

a

 Quick Installation Guide     

Содержание ML600


























Отзывы: