Acromag IP521-64 Series, Руководство пользователя

Страница: 13 / 28

SERIES IP521 INDUSTRIAL I/O PACK EIA/TIA-422B SERIAL COMMUNICATION MODULE
___________________________________________________________________________________________
- 13 -
EFR Bit FUNCTION PROGRAMMING
6 RTS
1
Hardware
Flow Control
0 = Disable Automatic RTS flow
control.
1= Enable Automatic RTS flow control.
The RTS pin can be automatically
controlled to indicate local buffer
overflows to remote buffers.
When automatic hardware flow
control is enabled, an interrupt will
be generated when the receive
FIFO is filled to the program trigger
level and RTS will go to a logic “1”
at the next trigger level. RTS will
return to a logic “0” when data is
unloaded below the next lower
trigger level. RTS functions
normally when hardware flow
control is disabled. FCTR bits0-1
are used to set the RTS delay
timer/trigger level.
7 CTS
2
Hardware
Flow Control
0 = Disable Automatic CTS flow
control.
1 = Enable Automatic CTS flow
control.
Notes :
1. For this model RTS is used to enable its corresponding
transmitter for output of the TxD signal. The RTS signals do
not have transmitter output paths on this model.
2. The CTS signals do not have a receiver input path on this
model.
A power-up or system reset sets all EFR bits to 0.
XON/XOFF-1,2 Registers, Ports A-H (R/W)
These registers hold the programmed XON and XOFF
characters for software flow control. XON or XOFF characters may
be 1 or 2 bytes long. The UART compares incoming data to these
values and restarts (XON) or suspends (XOFF) data transmission
when a match is detected. Note that access to these registers is
granted only after writing “BF” to the Line Control Register (LCR).
All XON/XOFF bits are set to 0 upon power-up or system reset.
Identification Space (Read Only, 32 odd-byte addresses)
Each IP module contains identification (ID) information that
resides in the ID space per the IP module specification. This area of
memory contains 32 bytes of information at most. Both fixed and
variable information may be present within the ID space. Fixed
information includes the "IPAC" identifier, model number, and
manufacturer's identification codes. Variable information includes
unique information required for the module. The IP521 ID Space
does not contain any variable (e.g. unique calibration) information.
ID Space bytes are addressed using only the odd addresses in a 64
byte block (on the “Big Endian” VMEbus). Even addresses are used
on the “Little Endian” PC ISA or PCI buses.
The IP521 ID Space contents are shown in Table 3.3. Note that
the base-address for the IP module ID space (see your carrier board
instructions) must be added to the addresses shown to properly
access the ID information. Execution of an ID Space Read
operation requires 0 wait states.
Table 3.3: IP521 ID Space Identification (ID)
Hex Offset
From ID
Base
Address
ASCII
Character
Equivalent
Numeric
Value
(Hex) Field Description
01 I 49 All IP's have 'IPAC'
03 P 50
05 A 41
07 C 43
09 A3 Acromag ID Code
0B 25 IP Model Code
1
0D 00 Not Used
(Revision)
0F 00 Reserved
11 00 Not Used (Driver
ID Low Byte)
13 00 Not Used (Driver
ID High Byte)
15 0C Total Number of ID
PROM Bytes
17 11 CRC
19 to 3F yy Not Used
Notes (Table 3.3):
1. The IP model number is represented by a two-digit code within
the ID space (the IP521 model is represented by 25 Hex).
THE EFFECT OF RESET
A software or hardware reset puts the serial channels into an
idle-mode until initialization (programming). A reset initializes the
receiver and transmitter clock counters. It also clears the Line-
Status Register (LSR), except for the transmitter shift-register empty
(TEMT) and transmit holding-register empty (THRE) bits which are
set to 1 (note that when interrupts are subsequently enabled, an
interrupt will occur due to THRE being set). The Modem Control
Register (MCR) is also cleared. All of the discrete signal lines,
memory elements, and miscellaneous logic associated with these
register bits are cleared, de-asserted, or turned off. However, the
Line Control Register (LCR), divisor latches, Receiver Buffer
Register (RBR), and Transmitter Holding Register (THR) are not
affected. The following table summarizes the effect of a reset on the
various registers and internal and external signals:
REG/SIGNAL RESET CTRL STATE/EFFECT
REGISTERS:
IER Reset All Bits low
ISR Reset Bit 0 high, Bits 1-7 low
LCR Reset All bits low
MCR Reset All bits low
FCR Reset All bits low
LSR Reset All bits low, except bits 5 & 6
are high
MSR Reset Bits 0-3 low, bit 4
corresponds to input signal
EFR Reset All bits low
XON-1,2 Reset All bits low
XOFF-1,2 Reset All bits low
TRG Reset All bits low