ACL Staticide ACL-750-USB Combo Tester Instructions
2/8/2021
8
4.
HARDWARE INSTALLATION
Before You Begin
1.
Make sure that a sample identification card has been sent to ACL Staticide for proper programming of the optional reader.
2.
Read the manual, help files, and other files on the C:\EsdTest directory.
3.
If user will not be using the software function of the ACL-750 meter, disregard the software instructions in this manual.
4.
Install the meter in view of the computer monitor, so employees that are testing can view the test results.
5.
Take a deep breath, and know that with the innovative product line of ACL Staticide there is instant peace of mind.
Meter Assembly
1.
For HID/CASI-RUSCO
/Indala/Motorola proximity card RS232 readers, a nine pin serial ports is required on your computer.
For USB compatible proximity card readers, at least one USB port is required on your computer for the reader, and for the
combo tester.
2.
Fasten the foot stand to the footplate. Place the foot stand on top of the footplate. Insert the small Allen head bolts through the
holes in the circular plate on the bottom of the stand. Position these bolts into the T nuts located in the bottom of the footplate
using the enclosed Allen head wrench. Tighten with Allen head wrench.
DO NOT OVER TIGHTEN
.
3.
Install the card reader if purchased on the right side or top of the top of the foot stand, where indicated by label. Place its cable
down through the rectangle hole. Then attach the ACL-750 meter on the left side on top of the foot stand, where indicated by
label. Place the meter so the top of the meter is flush with the top of the foot stand and is touching the HID reader on the right
side. With the non-proximity stand (Bar Code or Magnetic stripe) position the meter so that the USB cable does
NOT
protrude
from the bottom and cause interference with the person being tested. Place the bar code or mag stripe reader on
TOP
of the
stand.
4.
Attach the two-plug power supply cord (see Illustration 1 – A) to both the ACL-750 meter and to the HID/CASI-RUSCO
reader
(if purchased). If a USB reader is used, a power supply for the reader is not required. The male plug is attached to back of the
HID
reader, through the small round hole besides the reader. The female plug is attached to the ACL-750 meter up through
the hole of the stand into the front of the meter. Use hook/loop strips and attach the ACL-750 meter and the HID/CASI-
RUSCO
proximity reader to the stand. With the meter alone or with bar code or mag stripe attach the one power supply unit.
5.
Insert the cords and wires inside the back of the foot stand allowing wire slack. Place the enclosed plastic shroud over the wire
enclosure.
6.
The ACL750 USB meter is self-powered from the USB cable. If using the ACL780 meter (without USB) you will need to use the
12VDC power adapter cable or an alkaline battery.
7.
Insert the other ends of the signal cables into the computer.
8.
Plug the footplate lead (see Illustration 1 – C) completely into the combo tester socket "Heel Plate".
9.
Plug in any optional card reader power supplies.
10.
Remove the protective film from both the metal plates on the footplate.
11.
Turn on the computer. (Turning on the computer before the hardware is installed
may
not allow the Windows operating system
to properly run.)
Meter Adjustments
The ACL-750 can be adjusted to various electrical resistance specifications by opening the meter case and pressing the dipswitches
corresponding to the desired test ranges (see chart below).
For units manufactured after 3/12/2002, the ACL-750 will alarm
according to the EsdTest software set points, unless disconnected from the computer. The software parameters can be set in the
software under ‘Set up’, ‘User Information’, and entering desired information in ‘Strap Parameters’ In the individual User Information
menu . (see below), or later entered for everyone at once in the Setup “Change All Limits” menu (discussed later).
www.
.com
1.800.561.8187
