manualshive.com logo in svg

Acer Aspire M3985, Руководство по обслуживанию, Страница: 86 / 126

Поделиться
Скачать
Acer Aspire M3985 Скачать руководство пользователя страница 86

Chapter 4

78

Beep Codes

Beep codes are used by the BIOS to indicate a serious or fatal error to the end user. Beep codes are used 
when an error occurs before the system video has been initialized. Beep codes will be generated by the 
system board speaker, commonly referred to as the PC speaker. 

AMIBIOS displays the checkpoints in the bottom right corner of the screen during POST. This display method 
is limited, since it only displays checkpoints that occur after the video card has been activated.

Not all computers using AMIBIOS enable this feature. In most cases, a checkpoint card is the best tool for 

viewing AMIBIOS checkpoints.  

Beep Symptom

Cause and Description

One short beep

System is ready. 

System is OK.

Continuous one long beep

Memory not installed or memory error.

One long beep and two short beeps then 
repeat. 

VGA not installed or VGA error. 

Graphics card error/not installed, graphics card memory 
error or graphics card BIOS checksum error.

One long beep then two short beep

BIOS damaged.

BIOS is damaged, BIOS POST jumps to Boot Block to 
execute the default procedures. 

Two short beeps

CMOS damaged. 

CMOS checksum error or CMOS battery loss occurs. 

 

Содержание Aspire M3985































































































































Отзывы:

Нет отзывов