background image

 

3019 FLUORESCENCE MICROSCOPE SYSTEM   

 

 

 
 

ACCU-SCOPE

®

     

                   

73 Mall Drive, 

Commack, NY  11725  •  631-864-1000  •  www.accu-scope.com 

19

 

MAINTENANCE 

Please remember to 

never

 

leave the microscope with any of the objectives or eyepieces removed and 

always protect the microscope with the dust cover when not in use. 

 
 

 

SERVICE 

ACCU-SCOPE

 ®

 microscopes are precision instruments which require periodic servicing to keep them 

performing properly and to compensate for normal wear. A regular schedule of preventative maintenance 
by qualified personnel is highly recommended. Your authorized ACCU-SCOPE

 ®

 distributor can arrange 

for this service. Should unexpected problems be experienced with your instrument, proceed as follows: 
 
1. Contact the ACCU-SCOPE

 ®

 distributor from whom you purchased the microscope. Some 

problems can be resolved simply over the telephone. 
 
2. If it is determined that the microscope should be returned to your ACCU-SCOPE

 ®

 distributor or to 

ACCU-SCOPE

 ®

 for warranty repair, pack the instrument in its original Styrofoam shipping carton. If you 

no longer have this carton, pack the microscope in a crush-resistant carton with a minimum of three 
inches of a shock absorbing material surrounding it to prevent in-transit damage. The microscope should 
be wrapped in a plastic bag to prevent Styrofoam dust from damaging the microscope. Always ship the 
microscope in an upright position; 

NEVER SHIP A MICROSCOPE ON ITS SIDE

. The microscope or 

component should be shipped prepaid and insured. 

 
 

 

LIMITED MICROSCOPE WARRANTY

 

This microscope is  warranted to be free from defects in material and  workmanship for a period of five  years from 
the date of invoice to the original (end user) purchaser.  The mercury power supply is warranted for a period of one 
year from the date of invoice to the original (end user) purchaser.  This warranty does not cover damage caused in-
transit,  misuse, neglect,  abuse  or  damage  resulting  from  improper  servicing  or  modification  by  other  then  ACCU-
SCOPE  approved  service  personnel.    This  warranty  does  not  cover  any  routine  maintenance  work  or  any  other 
work, which is reasonably expected to be performed by the purchaser. Normal wear is excluded from this warranty. 
No  responsibility  is  assumed  for  unsatisfactory  operating  performance  due  to  environmental  conditions  such  as 
humidity, dust, corrosive chemicals, deposition of oil or other foreign matter, spillage or other conditions beyond the 
control  of  ACCU-SCOPE  INC.    This  warranty  expressly  excludes  any  liability  by  ACCU-SCOPE  INC.  for 
consequential loss or damage on any grounds, such as (but not limited to) the non-availability to the End  User of 
the product(s) under warranty or the need to repair work processes.  Should any defect in material, workmanship or 
electronic component occur under this warranty contact your ACCU-SCOPE distributor or ACCU-SCOPE at (631) 
864-1000.    This  warranty  is  limited  to  the  continental  United  States  of  America.    All  items  returned  for  warranty 
repair  must  be  sent  freight  prepaid  and  insured  to  ACCU-SCOPE  INC.,  73  Mall  Drive,  Commack,  NY    11725 

– 

USA.  All warranty repairs will be returned freight prepaid to any destination within the continental United States of 
America, for all foreign warranty repairs return freight charges are the responsibility of the individual/company who 
returned the merchandise for repair.  

 

ACCU-SCOPE is a registered trademark of ACCU-SCOPE INC., Commack, NY 11725 

 

 

 

Содержание 3019




















Отзывы: