AC Air Technology AC TRACKTECH T1X2 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 36

background image

14

1. Components

2-3 Adjusting the Wheel Cradle

2. Start Up Guide

1. When towing a non-fairing aircraft make sure the front and back cradle gates are ad-

justed in the fully extended position. For aircraft with fairings adjust the cradle gates
to the lowest setting. If extra clearance is needed position the

Booster Plate

on the

center of the mainplate between the tire guide spacers.

2. To adjust the front gate remove the ﬂ at head screws from each side and slide the

right and left ramp blocks to the desired position. Then reinstall the ﬂ at head screws
on each side. Note: It may be easier to remove these screws with the link locking
pins removed.

Ramp Blocks

Flat Head Screw

Flat Head Screw

Link Locking Pins

Booster Plate

«
...
12
13
14
15
16
...
»

Содержание AC TRACKTECH T1X2





































Отзывы:

Нет отзывов

Похожие инструкции для AC TRACKTECH T1X2

GM-FTDI2-LED16-C

Бренд: GearMo Страницы: 6

Бренд: Ampetronic Страницы: 2

Бренд: Weego Страницы: 6

TL-PA201 STARTER

Бренд: TP-Link Страницы: 2

Бренд: Royal Vendors Страницы: 2

Бренд: Adaptec Страницы: 8

Бренд: R&S Страницы: 66

Бренд: LSI Страницы: 46

Бренд: WMS Страницы: 16

Z-Stick Series 2

Бренд: Aeon Labs Страницы: 2

Бренд: Truma Страницы: 4

ExpressSAS R30F

Бренд: ATTO Technology Страницы: 2

Remote Supervisor Adapter

Бренд: IBM Страницы: 124

Бренд: MSI Страницы: 41

Бренд: MSI Страницы: 74

Бренд: 3idee Страницы: 4

Бренд: Belkin Страницы: 44

Бренд: Techly Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды