AC Air Technology AC TRACKTECH T1X2 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

background image

29

1. Components

2-10 Charging the Remote Control

2. Start Up Guide

Charging
Indicator
LED

Charging Jack

WARNING: Only use the supplied charger to charge the controller when using the

supplied batteries or the following:

- 1200mAh to 2200 mAh Ni-MH or Ni-Cd ‘AA’ Rechargeable Batteries

Using the remote control charger with alkaline batteries installed can damage the con-
troller. Do not use the charger if alkaline batteries are installed in the controller.

1. Plug the transmitter charger into a 110v AC wall socket.

2. Plug the connector from the charger into the charging jack on the transmitter. The

charging indicator LED, located on the side of the transmitter, will illuminate green
indicating the charger is charging. Once the transmitter is fully charged the charging
indicator LED will turn oﬀ .

3. The charging rate of the charger is 150mAh. When using the 1200mAh batter-

ies that are supplied, the radio requires an 8 hour charge when fully discharged
(1200/150=8). If using 2200mAh batteries, it will take approximately 15 hours to
charge (2200/150=14.6).

It is recommended to leave the remote controller charging when not in use.

«
...
27
28
29
30
31
...
»

Содержание AC TRACKTECH T1X2





































Отзывы:

Нет отзывов

Похожие инструкции для AC TRACKTECH T1X2

LinkStick WIS12ABGNX

Бренд: Samsung Страницы: 1

Бренд: Valcom Страницы: 4

Бренд: Valcom Страницы: 2

Бренд: Nextech Страницы: 7

Avaya one-X Gigabit Ethernet Adapter

Бренд: Avaya Страницы: 40

Бренд: Rosewill Страницы: 10

Бренд: StarTech.com Страницы: 2

Бренд: Acard Страницы: 35

Бренд: 3idee Страницы: 7

PowerGrid-9171n

Бренд: Comtrend Corporation Страницы: 55

Бренд: M&S Systems Страницы: 4

Бренд: Vantec Страницы: 13

Wake-On LAN Adapter

Бренд: Edimax Страницы: 8

Бренд: Teletronics International Страницы: 2

SNG 12/1500-OW-N

Бренд: VOLTCRAFT Страницы: 4

Бренд: Moen Страницы: 2

Бренд: ST-Lab Страницы: 4

ExpressSAS R30F

Бренд: ATTO Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды