AC Air Technology AC TRACKTECH T1X2 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 36

background image

21

3. Push the rail end forward using a small pry bar to tighten up the track. There should

be about a 1/2” of play at the center of the track.

Push Rail
End Forward

1/2” Up and Down Play at Center of Track

4. Tighten up all 3 retainer screws and reinstall the plastic track covers.

Install Plastic Track Cover Using 6 Screws.

5. Repeat steps 1 thru 4 for the other track.

«
...
19
20
21
22
23
...
»

Содержание AC TRACKTECH T1X2





































Отзывы:

Нет отзывов

Похожие инструкции для AC TRACKTECH T1X2

Бренд: Paradyne Страницы: 3

Бренд: Paradyne Страницы: 15

Бренд: Belkin Страницы: 18

Бренд: TAPaulk Communications Страницы: 3

Бренд: Omegon Страницы: 2

Бренд: Promise Technology Страницы: 41

Бренд: Bose Страницы: 124

Бренд: Amped Wireless Страницы: 2

Бренд: Devolo Страницы: 2

Бренд: HQ Страницы: 30

Бренд: GAI-Tronics Страницы: 4

VERDEdri 17-10504K

Бренд: World Dryer Страницы: 8

Бренд: Bosch Страницы: 8

Conettix ITS-D6682-INTL

Бренд: Bosch Страницы: 12

Бренд: Bosch Страницы: 80

Бренд: Bosch Страницы: 110

Бренд: Bosch Страницы: 96

Бренд: Bosch Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды