AC Air Technology AC TRACKTECH T1X2 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 36

background image

28

1. Components

2-9 Charging the Tug

2. Start Up Guide

Charging Jack

Charging Indicator

Light

1. Before charging your tug, the remote controller and tug should both be turned OFF.

2. The charging indicator LED should light up red once the charger is connected prop-

erly. The tug will be fully charged once the charger indicator LED turns green.

3. Leave the tug charging when it is not in use. The charger is equipped with “smart”

charging technology, preventing the battery from overcharging. Keeping the tug on its
charger this will prolong the life of the battery.

«
...
26
27
28
29
30
...
»

Содержание AC TRACKTECH T1X2





































Отзывы:

Нет отзывов

Похожие инструкции для AC TRACKTECH T1X2

USB 2.0 SATA & IDE Adapter 42868v0

Бренд: Lindy Страницы: 2

Бренд: Proyecson Страницы: 148

Бренд: Marshall Amplification Страницы: 6

Бренд: TRENDnet Страницы: 40

Бренд: dji Страницы: 40

Бренд: DeLOCK Страницы: 4

LANEscape WH2330

Бренд: Z-Com Страницы: 12

Бренд: Dension Страницы: 2

Бренд: ZyXEL Communications Страницы: 99

Бренд: Zeiss Страницы: 6

Бренд: MSI Страницы: 41

Бренд: MSI Страницы: 74

Бренд: KTI Networks Страницы: 23

Бренд: Linksys Страницы: 26

Бренд: Tripp Lite Страницы: 25

Hidden T-bar Frame Adapter PP-FCTA

Бренд: Premier Mounts Страницы: 2

Бренд: PROLiNK Страницы: 20

Бренд: ConnectGear Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды