AC Air Technology AC TRACKTECH T1X2 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 36

background image

10

1. Components

2-1 Remote Control Operation

2. Start Up Guide

Control Stick

Latch Switch

Power Indicator

LED

ON/OFF
Switch

Light Switch

3 Speed Toggle

Charging Indicator

LED

Charging Jack

Lanyard Anchor

Note:

The 3 Speed Toggle ranges from fast, to moderate, to slow. When operating the tug at
slow speed it may be necessary to switch to the moderate or fast speed mode on the
toggle when turning. Factors such as terrain and incline may aﬀ ect the maneuverability of
the tug. Adjust speed modes at your discretion.

1. Switch the remote control ON. The power indicator light turns on and the remote

control beeps once. If this does not happen, check the remote control battery con-
nection for proper installation. When the battery level is low, the remote control will
begin to beep repeatedly, signaling to replace or recharge the batteries.

«
...
8
9
10
11
12
...
»

Содержание AC TRACKTECH T1X2





































Отзывы:

Нет отзывов

Похожие инструкции для AC TRACKTECH T1X2

PoE Injector Adapter POE-32001T

Бренд: UNICOM Страницы: 1

BIC 1B0-IT1A7-Q40KFU-SM4A4A

Бренд: Balluff Страницы: 3

BAE PD-ML-010-04

Бренд: Balluff Страницы: 2

Бренд: Sena Страницы: 25

Бренд: tams elektronik Страницы: 21

DUAL-BAND Wi-Fi

Бренд: Belkin Страницы: 38

Бренд: Firmtech Страницы: 68

Adapt Reference

Бренд: Dense Страницы: 9

Бренд: Greenlee Страницы: 36

Бренд: Cables to Go Страницы: 9

Бренд: Manhattan Страницы: 2

Бренд: BeachTek Страницы: 2

Бренд: Emulex Страницы: 21

FM 5 IN DASH ADAPTER KIT

Бренд: Eagle Страницы: 5

Бренд: oticon Страницы: 54

CardPark APA-4510

Бренд: Adaptec Страницы: 8

Бренд: Protectowire Страницы: 2

FriendlyNET GigaNIX 1000TA/TPC

Бренд: Asante Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды