MB EVO PRO/MB EVO
3 Product description
EN
-
27
• Any metal vapors, especially lead, cadmium, copper and beryllium are
harmful! Ensure sufficient ventilation or extraction. Do not exceed the
current MAC values.
• Rinse work-pieces that have been degreased with chlorinated solvents
with clear water. Otherwise there is a risk of phosgene gas formation.
For the same reason, no degreasing baths containing chlorine must be
placed in the vicinity of the welding area.
• In connection with various welding torches, there may be other hazards,
for example those caused by: electrical current (power supply, internal
circuit), welding spatter with regard to combustible or explosive materials,
UV radiation from the arc, smoke and vapors.
• Adhere to the general fire protection regulations and remove
inflammable materials from the surroundings of the welding work area,
prior to starting work. Even hours after finishing the welding work, there
is a risk of late ignition caused by sparks. Place appropriate fire
extinguishing equipment in the workplace within easy reach.
2.5
Technical State
• Do not exceed the maximum limit values of the load data. Overloading
leads to torch destruction.
• Do not make any constructive changes to this device.
• During welding work outdoors, use suitable protection against the
effects of weather.
2.6
Protective clothing
• Do not wear loose fitting clothing or jewelry.
• Use a hair net for long hair.
• During operation of the welding torches and in connection with the
welding process, always wear safety goggles, protective gloves and, if
required, a breathing mask.
2.7
Classification of the warnings
The warnings used in the operating instructions are divided into four different
levels and shown prior to potentially dangerous work steps.
Arranged in descending order of importance, they have the following
meanings:
2.8
Emergency information
In the event of an emergency, immediately disconnect the following supplies:
• Electrical power supply, compressed air, coolant and shielding gas.
Further measures can be found in the “Power source” operating instructions
or the documents for further peripheral devices.
3 Product description
3.1
Technical data
DANGER
Describes an imminent threatening danger. If not avoided, this will result in fatal or extremely critical injuries.
WARNING
Describes a potentially dangerous situation. If not avoided, this may result in serious injuries.
CAUTION
Describes a potentially harmful situation. If not avoided, this may result in slight or minor injuries.
NOTICE
Describes the risk of impairing work results or potential material damage to the equipment.
WARNING
Hazards caused by improper use
If improperly used, the device can present risks to persons, animals and material property.
• Use the device according to its designated use only.
• Do not convert and modify the device to enhance its performance without authorization.
• Only qualified personnel are permitted to perform work on the device or system.
Transport and storage
−25° C to +55° C
Shielding gas (DIN EN ISO 14175)
CO
2
and mixed gases M21
Relative humidity
Up to 90 % at 20 °C
Wire types
Commercially available round wires
Type of use
Hand-held
Voltage rating
Peak value of 113 V
Type of voltage
DC
Protection type of the device
connections (EN 60529)
IP3X
Polarity of the electrodes for DC
Usually positive
Control features in the handle
For 42 V and 0.1 to 1 A
Tab. 1
General torch data (EN 60974
-
7)
Содержание MB EVO PRO
Страница 14: ...BG 14 5 MB EVO PRO MB EVO 3 4 4 5 4 6 1 2 3 4 5 2 5 1 2 C 1 2 6 1 2 3 7 1 2 3 8 8 1 F 5...
Страница 67: ...MB EVO PRO MB EVO 2 JA 67 2 3 2 4 MAC UV 2 5 2 6 2 7 4 2 8...
Страница 143: ...MB EVO PRO MB EVO 2 ZH 143 2 3 2 4 MAK 2 5 2 6 2 7 2 8...
Страница 145: ...MB EVO PRO MB EVO 4 ZH 145 4 4 1 1 2 4 2 MIG MAG 8 ZH 146 4 3 A 1 2 3 ABICOR BINZEL BTC 4 4 B 1 2 3 4 4 5 4 6 1 2 3 4...
