Abell Adrenaline 3D V2 Скачать руководство пользователя страница 2

Страница: 2 / 19

Here’s what ya get!

Main Wing (1)
Ailerons

(2)

Fuselage Side Front Left (1)

Fuselage Side Front Right (1)

Fuselage Sides Center (2)

Main Fuselage (1)

Rudder

(1)

Horizontal Stabilizer (1)

Elevators

(2)

4-40 x 3/8” Socket Head Cap Screws (4)

#4 Flat Washers (2)

Hinges

(15)

Push Rod Guides (2)

3/8”x 1” Shrink Tube (1)

Control Horns (4)

Control Horn Retainers (4)

Clevises

(8)

3/16”x 36” Carbon Fiber Wing Spar (1)

1/16”x 3/16” x 36” Carbon Fiber Sticks (4)

1/16”x 24” Round Carbon Fiber Rod (2)

3/16”x 16” Round Composite Tube (1)

Decals

Here’s what you’ll need!

Abell Hobby Super Gold + Odorless CA, Abell Hobby Insta-Set Accelerator, 1/6” Drill Bit, 5/64”

Drill Bit, Hobby Knife, Small piece of 3/16” or 1/4" Brass or Aluminum Tubing, Masking Tape, 3M

Hook & Loop (Velcro), Cutting tool to cut Carbon Fiber, 3/32” Allen Wrench, Soldering Iron &

Solder, Sand Paper and Sanding Block.

Содержание Adrenaline 3D V2




















Результаты поиска

Содержание Adrenaline 3D V2

Отзывы:

Бренды по названию

Популярные бренды

Abell Adrenaline 3D V2, Руководство пользователя

Результаты поиска

Содержание Adrenaline 3D V2

Отзывы:

Бренды по названию

Популярные бренды