ABB Zenith ZBTS T Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 112

ABB Zenith ZBTS T Series Скачать руководство пользователя страница 45

45

3 4ZBT S _ 3 0 -1 2 0 0A rev. A / 1 S CC 3 0 3 0 4 3 M 0 2 01

1

—

4. Electronic Accessories

Ekip Connect Sofware and Programming
-modules are suitable for both ATS and
Bypass switches.
• Ekip Connect -software
• Ekip Programming -module

—
Fig. 4.1 Programming module

Both switches already have a factory-in-
stalled I/O signal modules Ekip Signaling
2K-1 and Ekip Signaling 2K-2 powered by
auxiliary power supply module OXEA1 in
fixed Bypass switch and in Connection
Module in draw-out switch (ATS always)
powered by Ekip supply module.

NOTE!

It is still possible to add two pieces

of Ekip modules to the fixed Bypass switch
version, and one Ekip module to the Con-
nection Module of draw-out switch version
(ATS always), eg. an Ekip Signaling 2K-3
and/or alternatively a communication
module Ekip Com module. See mounting
instructions on Part 2, Chapter 8.

The suitable Ekip modules of which one or
two can be added:
• Ekip signalling modules;

- Ekip signalling 2K-3-OX

• Ekip Com modules;

- Ekip Com Modbus RTU-OX
- Ekip Com Modbus TCP-OX
- Ekip Com Profibus DP
- Ekip Com DeviceNet
- Ekip Com Profinet
- Ekip Com EtherNet/IP
- Ekip Com Hub

—
Fig. 4.2 Ekip Signalling and Com -modules are possible
to add (two pieces) to fixed Bypass switch powered
by the auxiliary power supply module, OXEA1

—
Fig. 4.3 Ekip Signalling or Com -module is possible to add
to the Connection module of the draw-out switch powered
by the auxiliary power supply module = Ekip Supply module

Warning

Hazardous voltage may be present within the

panel when connecting electronic accessories.

Remove all sources of power to the ATS / By-

pass panel before connecting Ekip modules.

Notice

For more information of Ekip software or

these above mentioned modules, see manual:

Automatic transfer switches TruONE™ ATS,

OX_ 30. . .1600_, 34OX_30-1600 /

1SCC303011M0201, Chapter 5, Electronic ac-

cessories.

«
...
43
44
45
46
47
...
»

Содержание Zenith ZBTS T Series

















































































































Отзывы:

Нет отзывов