manualshive.com logo in svg

ABB Zenith ZBTS T Series, Инструкция по установке и эксплуатации, Страница: 37 / 112

Поделиться
Скачать
ABB Zenith ZBTS T Series Скачать руководство пользователя страница 37

37

3 4ZBT S _ 3 0 -1 2 0 0A  rev. A  /  1 S CC 3 0 3 0 4 3 M 0 2 01

1

Switch in O position

ATS Test

Load Current

.... A

00:34

G

TruONE ATS

Switch Overview

 

 S1 p 

     Ok                           Ok    

 S2

— 
Fig. 3.21  HMI of ATS,  ATS status is Test,  
see also the Fig. 3.29

After the button is returned the HMI of 
ATS switch shows when switch is in Test 
location, the indication is: “ATS TEST”, see 
Fig. 3.21. 

In test location, the ATS is disconnected 
from the load, but control power is avail-
able. All electrical operations are allowed 
to ATS.

3.4.1.4  Step 4: Operate ATS to ISOLATED 
Location with the Racking in/out tool
Push the button of the ATS Racking out 
mechanism and rotate counterclockwise 
with the Racking in/out tool until button 
returns. See the detailed instructions in 
paragraph 3.4.2 "How to use the draw-out 
mechanism to rack out the switch".

— 
Fig. 3.22  Racking out mechanism of ATS, Push the 
button and rotate counterclockwise with Racking in/
out tool up to Isolation location, see also the Fig. 3.28

The switch and HMI of ATS has now lost 
the power, the ATS is completely discon-
nected from the system load and control 
power. It is now safe to open the door and 
the ATS can be removed from the cabinet. 
Lift ATS out of the track if needed. The
fixing screws must be unfasten. See the 
lifting instructions in Part 2, Chapter 7 
Installation.

After the isolation operation of ATS the 
Bypass switch is feeding the system load 
and it is highly recommended to set the 
Bypass switch to Operation mode: Auto, if 
not set earlier in Step 2. If Bypass switch 
is connected on Source 1 and if this 
source fails, Bypass switch will automati-
cally start the generator and when this 
source (Source 2) is available, Bypass 
switch automatic transfer to this available 
source. This is only available when the By-
pass switch is set to Operation mode: 
Auto.

Содержание Zenith ZBTS T Series

















































































































Отзывы:

Нет отзывов