ABB Zenith ZBTS T Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 112

ABB Zenith ZBTS T Series Скачать руководство пользователя страница 32

32

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N A N D O PER ATI N G I N S TR U C TI O N

1

3.3.1.3 Main Menu

—
Fig. 3.13 By touching on Start Menu lower left corner
-image you can move to the Main Menu page of
Operation, Parameters, Measurements, Settings, Test
and About, see the table below for the selections

TruONE ATS

Overviews

Main Menu

Measures

Analog Meters

Overviews

Switch Overview

Operation

Parameters

Measurements

About

Test

Settings

TruONE ATS

Notice

When you have changed the parameter, go

always back in the menu and confirm the

change always when asked.

Notice

The default values are marked in the menu

tree by *-marking.

NOTE! Setting the switch to AUTO mode:

MAIN MENU –> Operation –> Operation
Mode –> AUTO, see the table on next
page.

Operation modes:
• Bypass switch default settings:

MAN permanent

• ATS switch default settings:

MAN momentary

NOTE!

If the switch is controlled with the

HMI keys I-O-II, the switch mode automat-
ically switches to MAN momentary mode.

NOTE!

See the "BASIC OPERATION IN-

STRUCTION" on the door of Bypass-Isola-
tion Automatic Transfer Switch and more
detailed information from chapter 3.4
"Description of Basic Functionality".

When connecting the Bypass-Isolation
Automatic Transfer Switch to operation
the Operation modes of the switches
have to set:
• In ATS HMI operations menu, set ATS to

AUTO mode.

• In Bypass HMI operations menu, set By-

pass switch to MAN Permanent mode.

«
...
30
31
32
33
34
...
»

Содержание Zenith ZBTS T Series

















































































































Отзывы:

Нет отзывов