manualshive.com logo in svg

ABB Zenith ZBTS T Series, Инструкция по установке и эксплуатации, Страница: 16 / 112

Поделиться
Скачать
ABB Zenith ZBTS T Series Скачать руководство пользователя страница 16

16

Zenith ZBTS T-series 100-1200A, I N S TA LL ATI O N  A N D  O PER ATI N G  I N S TR U C TI O N

1

 

Notice

 

A protective device such as a moulded case 

circuit breaker or fused disconnect switch 

MUST be installed on both sources of incom-

ing power for circuit protection and as a dis-

connection device.

The Bypass-Isolation Automatic Transfer 
Switch consists of these main modules:
•  The two automatic transfer switches:

 - ATS is always draw-out version (lower 

switch module)

 - Bypass can be fixed or draw-out 

version (upper switch module)

•  Customer main connections, Source 1, 

Source 2 and Load, on the top of the 
cabin 

•  The Control Plate (bottom module)

 - Customer connections: Generator 

start/stop terminals

 - Control circuit
 - Place for optional accessories

•  Racking in/out -mechanism
•  Both switches have operation panel HMI 

at the door

The modules containing the switch are 
connected to the busbars located at the 
rear of the modules and the entire pack-
age is mounted in an enclosure. The ATS 
switch in the lower switch module is al-
ways a draw-out version that includes an 
in/out rack for easy maintenance. The up-
per switch module, the Bypass switch, is 
available in either a fixed or draw-out ver-
sion, but all the functions are exactly the 
same both Bypass and ATS switches.

The top module of enclosure is for cable 
lugs for Source 1, Source 2 and for Load. 
The lugs are located behind transparent 
covers. See the location of lugs in Fig. 2.6. 

The Control Plate is located in the bottom 
module equipped with own inside door. 
The front side of the door is reserved for 
the customer connections e.g. generator 
start/stop terminals and also included an 
empty space for the accessories. Back 
side of the Control Plate door are all other 
components which are necessary for the 
control system.

The switch racking in/out mechanism is 
on enclosure’s door also in the upper 
switch module, when the Bypass switch is 
draw-out version. The tool for the racking 
in/out system is located in the mecha-
nism behind the transparent cover. The 
default location is the lower switch mod-
ule, where ATS is always the draw-out 
version.

 

Danger

 

Hazardous voltage. Turn OFF all power before 

installation, adjustment, or removal of the 

transfer switch or any of its components.

 

Warning

 

Due to hazardous voltage and current, ABB 

recommends that ABB certified technician or 

qualified electrician perform the installation 

and maintenance.

Содержание Zenith ZBTS T Series

















































































































Отзывы:

Нет отзывов