manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Руководство пользователя

Поделиться
Скачать
ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 72

- 72 -

000995AG

5 - Installation

D

istribution grid output connection (AC side)

To connect the inverter to the grid you need 4 connections: ground, neu-

tral, phase and external grounding protection 

In any case, connection 

of the inverter to ground is mandatory.

Any failure of the inverter when it is not connected to ground through the appropriate terminal 

(AC connector) and to the metal frame (external grounding protection) is not covered by the 

warranty.

The connection of the grid cable to the inverter is realised through the 

dedicated AC output connector 

10

 by carrying out the following opera-

tions:

• Characteristics and sizing of the line cable
• Installation of the cable on the AC output connector 

10

• Connection of the AC output connector to the inverter

C

haracteristics and sizing of the line cable

The cross-section of the AC line conductor must be sized in order to pre-

vent unwanted disconnections of the inverter from the grid due to high 

impedance of the line that connects the inverter to the power supply; If 

the impedance is too high it causes an increase in the AC voltage which, 

on reaching the limit set by the standards in the country of installation, 

causes the inverter to switch off.

In order to allow installation of the grid cable inside the AC output con-

nector 

10

, the sizings indicated in the figure must be observed

Ø10÷14mm

max. 6 mm²

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды