manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Руководство пользователя

Поделиться
Скачать
ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 181

- 181 -

000700CG

8 - Maintenance

- Code on display

- Error message 

- Signal

Name of Alarm and Cause

Solution

 E081

- Internal Error

-   

GFI LED

Inverter fault / Incomplete inverter closing:

Fault inside the inverter or incomplete inverter clos-

ing (front cover missing or not tightened, cable glands 

missing or incorrectly tightened, environmental protec-

tion IP65 not guaranteed)

• If the problem has occurred during the installation phase or 

during the inverter maintenance phase (therefore the cover 

has been removed or the cable glands have been acted upon), 

carry out the following operations:

- Disconnect the AC grid and DC input from the inverter and 

check for the front cover and all the cable glands, also check-

ing their correct tightening to ensure environmental protection 

IP65; reconnect the AC grid and the DC input and attempt to 

switch the inverter on; if the problem persists, contact customer 

assistance :

- If the front cover and all cable glands are present, discon-

nect the AC grid and DC input from the inverter and wait 15 

minutes at a safe distance, then open the inverter cover and 

if no smoke/smell of burning is present, check the integrity of 

the components or the presence of moisture or other abnormal 

conditions; reconnect the AC grid and DC input and attempt to 

switch on the inverter; if the problem persists contact customer 

assistance.

• If the problem has occurred after installation or after an in-

verter maintenance phase (therefore the cover has NOT been 

removed or the cable glands have NOT been acted upon), dis-

connect the AC grid and the DC input from the inverter and 

contact customer assistance.

 E084

- BackFeed OC

-   

Alarm LED

Return current to photovoltaic field:

The error occurs if the input voltage is particularly low 

(typically in the evening in conditions of low irradiation) 

and indicates a return current from the inverter to the 

photovoltaic panels).

If the error occurs in the evening or in conditions of low irra-

diation, it must not be considered a problem but a protection 

intervention for the photovoltaic field.

- If the problem occurs with good irradiation conditions, switch 

the inverter off and back on again; if the error persists, contact 

customer assistance.

 E089

- Wrong Wiring

-   

Alarm LED

Incorrect grid wiring connection on Stand Alone:

The error occurs if the grid cables have been incor-

rectly connected to the Stand Alone output.

• Check that the cables on the Stand Alone output have been 

installed correctly.

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды