ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 111

Страница: 111 / 198

- 111 -

000698DG

7 - Operation

escription of the Web user interface

The UNO-DM-TL-PLUS inverters are equipped with an advanced in-

tegrated web user interface and user interface that allow a full access

to all configuration and comissioning parameters from any electronic

device (laptop, tablet and smartphone).

The screenshots shown in this chapter are indicatives and it could be changed without any

notification.

ccess to the Web user interface

To access to the web user interface is required to connect a device equip-

ped with wireless connection (such as tablet, laptop or smartphone).
Depending on completion of STEP #2 of the wizard commissioning pha-

se (the inverter was connected to the domestic wireless network (“Sta

tion Mode”), or this step was skipped) it’s required to follow one of the two

procedures described below:

Connection to the inverter in “Station Mode”

If the inverter was connected to the domestic wireless network, follow

this procedures:
• Enable the wireless connection on the device (tablet, smartphone or

laptop) and connect it to the same wireless network to which the inverter

is connected.
• Open an internet browser (reccomended browser: Chrome versions

from v.55, Firefox versions from v.50) and enter the IP Address assigned

by the router to the inverter, or the “Host Name” (that could be obtained

writing this url:

http://ABB-XX-XX-XX-XX-XX-XX.local

replacing the

“

” with the hex digits of the wireless MAC address of the inverter (it can

be found on the “Wireless Identification Label” placed on the side of the

inverter or applied during the commissioning phase to the quick installa-

tion guide on cover page)), to access the login page.

In order to use the “Host Name” as an alternative to the dynamic IP address, the Wi-Fi router

to which the board is connected (when operating in “Station Mode”) must provide the Domain

Name System (DNS) service (contact the network administrator for further information regar-

ding the presence or absence of the DNS service in the Wi-Fi router or how to enable it). In this

way, even if the IP address assigned to the inverter should change over time, (dynamic IP), it

will always be possible to use the same “Host Name” which will remain unchanged over time.

Android devices doesn’t allow the use of “Host Name” to access to the web user interface!

The IP address assigned may vary for reasons connected to the wireless home router setup

(for example, a very brief DHCP lease time). If verification of the address is required, it is

usually possible to obtain the client list (and the corresponding IP addresses) from the wire-

less router administration panel.

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Результаты поиска

Содержание UNO-DM-1.2-TL-PLUS

Отзывы:

Бренды по названию

Популярные бренды

ABB UNO-DM-1.2-TL-PLUS, Руководство пользователя

Результаты поиска

Содержание UNO-DM-1.2-TL-PLUS

Отзывы:

Бренды по названию

Популярные бренды