ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 28

- 28 -

000680EG

3 - Characteristics

UNO-DM-3.3

UNO-DM-4.0

Input Side

Absolute maximum DC input voltage (Vmax,abs)

600 V

Start-up DC input voltage (Vstart)

200 V  (adj. 120...350 V)

Operating DC input voltage range (Vdcmin...Vdcmax)

0.7 x Vstart...580 V (min 90 V)

Rated DC input voltage (Vdcr)

360 V

Rated DC input power (Pdcr)

3500 W

4250 W

Number of independent MPPT 

2

Maximum DC input power for each MPPT (PMPPTmax)

2000 W

3000 W

DC input voltage range with parallel configuration of 

MPPT at Pacr

170...530 V

130...530 V

DC power limitation with parallel configuration of MPPT

Linear derating from Max to 

Null [530V≤VMPPT≤580V]

Linear derating from Max to 

Null [530V≤VMPPT≤580V]

DC power limitation for each MPPT with independent 

configuration of MPPT at Pacr, max unbalance example

2000 W [200V≤VMPPT≤530V]

 

the other channel:

Pdcr-2000W  

[112V≤VMPPT≤530V]

3000 W [190V≤VMPPT≤530V]

 

 the other channel:

Pdcr-3000W  

[90V≤VMPPT≤530V]

Maximum DC input current (Idcmax) / for each MPPT 

(IMPPTmax)

20.0 A / 10.0 A

32.0 A / 16.0 A

Maximum return current (AC side vs. DC side)

< 5 mA (In case of failure, limited by the external 

protection provided on the AC circuit)

Maximum input short circuit current / for each MPPT

12.5 A / 25.0 A

20.0 A / 40.0 A

Number of DC inputs pairs for each MPPT

1

DC connection type 

Quick Fit PV Connector 

(1)

Type of photovoltaic panels connectable in input 

according to the IEC 61730 standard

Class A

Input protection

Reverse polarity protection 

Yes, from limited current source

Input over voltage protection for each MPPT - varistor

Yes

Photovoltaic array isolation control

According to local standard

DC switch rating for each MPPT (version with DC 

switch) 

25 A / 600 V 

Output Side

AC Grid connection type

Single phase

Rated AC power (Pacr @cosφ=1 )

3300 W

4000 W

Maximum AC output power (Pacmax @cosφ=1)

3300 W

4000 W 

(2)

Maximum apparent power (Smax)

3300 VA

4000 VA 

(2)

Rated AC grid voltage (Vac,r)

230 V

AC voltage range

180...264 V 

(3)

Maximum AC output current (Iac,max)

14.5 A

17.2 A 

(2)

Contributory fault current

16.0 A

19.0 A

Rated output frequency (fr)

50 Hz - 60 Hz 

(4)

Output frequency range (fmin...fmax)

47...53 Hz / 57 ...63Hz

(4)

Nominal power factor and adjustable range

> 0.995, adj. 0.1 - 1 (over/under excited)

Total current harmonic distortion

< 3.5

AC connection type

Female connector from panel

Output protection

Anti-islanding protection

According to local standard

Maximum external AC overcurrent protection

20.0 A

25.0 A 

Output overvoltage protection - varistor

2 (L - N / L - PE)

Operating performance

Maximum efficiency (ηmax)

97.0%

97.0%

Weighted efficiency (EURO/CEC)

96.5% / -

96.5% / -

Feed in power threshold

8.0 W

Night consumption

< 0.4W

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Отзывы: