ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 127

Страница: 127 / 198

- 127 -

000698DG

7 - Operation

• Configurable alarm with reset at the end of the alarm signalling pro

cess - display text “Alarm-Contact (alarm configurable - no-latch)”

The relay is activated (status: switched) whenever an error (code Exxx)

or a warning (code Wxxx) is present from those selected from the list in

the dedicated submenu

Alarm Config

of the inverter display. The con-

tact returns to its resting position when the alarm signal ends, i.e. before

the inverter checks the grid after the alarm state. This is because grid

control state is not an alarm state but a state of normal operation.

Alarms for which the relay is activated

E001

E002

E003

E004

E005

E006

E007

E010

E011

E012

E013

E014

E015

E016

E018

E019

E020

E021

E022

E023

E025

E026

E027

E028

E029

E030

E031

E032

E033

E034

E036

E037

E046

E050

E051

E053

E054

E055

E056

E057

E058

E065

E066

E067

E068

E069

E070

E074

E077

E078

E080

E084

E086

E087

E088

E089

W002

W003

W004

W005

W006

W007

W009

W011

W015

W017

W018

W019

W021

W022

W023

W024

W025

W027

W029

W030

W031

W037

W039

W040

W042

W043

W046

W047

W048

W051

W058

W059

For the configurable relay operating mode “Alarm Conf.”, the following considerations are

valid:
If the alarm condition is persistent, the alarm contact cyclically switches from its resting state

to its activated state.

In the presence of W002 signalling (Input UV – input voltage below the limit of operation),

the alarm contact switches to then reset itself at the end of the alarm signal. This means that

during the reduced input voltage (display message “Waiting Sun”) the alarm contact remains

in its resting position.
In the presence of W003, W004, W005, W006, W007 signalling, the alarm contact switches

to then reset itself at the end of the alarm signal. This means that during the absence of grid

voltage (display message “Missing Grid”) the alarm contact remains in its resting position.

INVERTER RUN

SELECTED

ERROR/WARNING

OCCURENCY

ERROR MESSAGE

t=15s

GRID RECONNECTION

t=based on Country Standard

ERROR/WARNING

STILL

PRESENT

Yes

N.C.

N.O.

N.C.

N.O.

Relay State:

Idle

N.C.

N.O.

Relay State: Switched

Relay State:

Idle

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Результаты поиска

Содержание UNO-DM-1.2-TL-PLUS

Отзывы:

Бренды по названию

Популярные бренды

ABB UNO-DM-1.2-TL-PLUS, Руководство пользователя

Результаты поиска

Содержание UNO-DM-1.2-TL-PLUS

Отзывы:

Бренды по названию

Популярные бренды