manualshive.com logo in svg

ABB UNO-DM-1.2-TL-PLUS, Руководство пользователя

Поделиться
Скачать
ABB UNO-DM-1.2-TL-PLUS Скачать руководство пользователя страница 16

- 16 -

000919AG

2 - Introduction and general information

A

pplication area, general conditions 

ABB shall not be liable for any damages whatsoever that may result from 

incorrect or careless operations.

You may not use the equipment for a use that does not conform to that provided for in the 

field of use. The equipment MUST NOT be used by inexperienced staff, or even experienced 

staff if carrying out operations on the equipment that fail to comply with the indications in this 

manual and enclosed documentation.

I

ntended or allowed use

This equipment is a inverter designed for:

transforming a continuous electrical current (DC) 

supplied by a photovoltaic generator (PV) 

in an alternating electrical current (AC) 

suitable for feeding into the public distribution grid.

L

imits in field of use

The inverter can be used only with photovoltaic modules which have ground isolated input 

poles.

Only a photovoltaic generator can be connected in the input of the inverter (do not connect 

batteries or other sources of power supply).

The inverter can be connected to the electricity grid only in countries for which it has been 

certified/approved.

The inverter cannot be connected to the DC side in parallel to other inverters.

The inverter may only be used in compliance with all its technical characteristics.

I

mproper or prohibited use 

IT IS STRICTLY FORBIDDEN TO:

• 

Install the equipment in environments subject to particular conditions of flammability or in 

adverse or disallowed environmental conditions, (temperature and humidity).

• 

Use the equipment with safety devices which are faulty or disabled.

• 

Use the equipment or parts of the equipment by linking it to other machines or equipment, 

unless expressly provided for.

• 

Modify operating parameters that are not accessible to the operator and/or parts of the 

equipment to vary its performance or change its isolation.

• 

Clean with corrosive products that could corrode parts of the equipment or generate elec-

trostatic charges.

• 

Use or install the appliance or parts of it without having read and understood the contents of 

the user and maintenance manual.

• Placing any heavy object, sit or stand up on the inverter.

• 

Heat or dry rags and clothing on the parts in temperature. In addition to being hazardous, 

doing so would compromise component ventilation and cooling.

Содержание UNO-DM-1.2-TL-PLUS







































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды