ABB RELION 650 SERIES Скачать руководство пользователя страница 94

Страница: 94 / 262

ITrip: The steady state current that the transformer can withstand. The setting is given in % of

IBase1 or IBase2.

Alarm1: Heat content level for activation of the signal ALARM1. ALARM1 is set in % of the trip heat

content level.

Alarm2: Heat content level for activation of the output signal ALARM2. ALARM2 is set in % of the

trip heat content level.

LockoutReset: Lockout release level of heat content to release the lockout signal. When the

thermal overload protection trips a lock-out signal is activated. This signal is intended to block

switching on of the protected circuit transformer as long as the transformer temperature is high.

The signal is released when the estimated heat content is below the set value. This temperature

value should be chosen below the alarm temperature.

LockoutReset is set in % of the trip heat

content level.

Warning: If the calculated time to trip factor is below the setting Warning a warning signal is

activated. The setting is given in minutes.

7.4

Breaker failure protection 3-phase activation and output

CCRBRF (50BF)

IP14514-1 v4

7.4.1

Identification

M14878-1 v4

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Breaker failure protection, 3-phase

activation and output

CCRBRF

3I>BF

SYMBOL-U V1 EN-US

50BF

7.4.2

Application

M13916-3 v5

In the design of the fault clearance system the N-1 criterion is often used. This means that a fault

needs to be cleared even if any component in the fault clearance system is faulty. One necessary

component in the fault clearance system is the circuit breaker. It is from practical and economical

reason not feasible to duplicate the circuit breaker for the protected component. Instead a

breaker failure protection is used.

Breaker failure protection, 3-phase activation and output (CCRBRF, 50BF) will issue a back-up trip

command to adjacent circuit breakers in case of failure to trip of the “normal” circuit breaker for

the protected component. The detection of failure to break the current through the breaker is

made by means of current measurement or as detection of remaining trip signal (unconditional).

CCRBRF (50BF) can also give a re-trip. This means that a second trip signal is sent to the protected

circuit breaker. The re-trip function can be used to increase the probability of operation of the

breaker, or it can be used to avoid back-up trip of many breakers in case of mistakes during relay

maintenance and test.

Section 7

1MRK 505 287-UUS B

Current protection

Busbar protection REB650

Application manual

Содержание RELION 650 SERIES






































































































































































































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды

ABB RELION 650 SERIES, Руководство по применению

Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды