ABB RELION 650 SERIES Скачать руководство пользователя страница 59

Страница: 59 / 262

GUID-D20BB1F1-FDF7-49AD-9980-F91A38B2107D V1 EN-US

Figure 20: Alarm LED panel

The function button and alarm LED panels are not visible at the same time. Each panel is shown by

pressing one of the function buttons or the Multipage button. Pressing the ESC button clears the

panel from the display. Both the panels have dynamic width that depends on the label string

length that the panel contains.

5.1.2

LEDs

AMU0600427 v9

The LHMI includes three protection status LEDs above the display: Normal, Pickup and Trip.

There are 15 programmable alarm LEDs on the front of the LHMI. Each LED can indicate three

states with the colors: green, yellow and red. The alarm texts related to each three-color LED are

divided into three pages.

There are 3 separate pages of LEDs available. The 15 physical three-color LEDs in one LED group

can indicate 45 different signals. Altogether, 135 signals can be indicated since there are three LED

groups. The LEDs can be configured with PCM600 and the operation mode can be selected with

the LHMI or PCM600.

There are two additional LEDs which are embedded into the control buttons

and

. They

represent the status of the circuit breaker.

5.1.3

Keypad

AMU0600428 v14

The LHMI keypad contains push-buttons which are used to navigate in different views or menus.

The push-buttons are also used to acknowledge alarms, reset indications, provide help and switch

between local and remote control mode.

The keypad also contains programmable push-buttons that can be configured either as menu

shortcut or control buttons.

1MRK 505 287-UUS B

Section 5

Local human-machine interface

Busbar protection REB650

Application manual

Содержание RELION 650 SERIES






































































































































































































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды

ABB RELION 650 SERIES, Руководство по применению

Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды