ABB RELION 650 SERIES Скачать руководство пользователя страница 183

Страница: 183 / 262

10.7.3

Setting guidelines

SEMOD176518-4 v4

The parameters for the single point generic control 8 signals (SPC8GGIO) function are set via the

local HMI or PCM600.

Operation: turning the function operation Enabled/Disabled.

There are two settings for every command output (totally 8):

Latchedx: decides if the command signal for output x is Latched (steady) or Pulsed.

tPulsex: if Latchedx is set to Pulsed, then tPulsex will set the length of the pulse (in seconds).

10.8

Automation bits AUTOBITS

10.8.1

Identification

GUID-C3BB63F5-F0E7-4B00-AF0F-917ECF87B016 v3

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

AutomationBits, command function

for DNP3

AUTOBITS

10.8.2

Application

SEMOD158637-5 v4

The AUTOBITS function block (or the automation bits function block) is used within PCM600 in

order to get into the configuration the commands coming through the DNP3 protocol.AUTOBITS

function block have 32 individual outputs which each can be mapped as a Binary Output point in

DNP3. The output is operated by a "Object 12" in DNP3. This object contains parameters for

control-code, count, on-time and off-time. To operate an AUTOBITS output point, send a control-

code of latch-On, latch-Off, pulse-On, pulse-Off, Trip or Close. The remaining parameters are

regarded as appropriate. For example, pulse-On, on-time=100, off-time=300, count=5 would give 5

positive 100 ms pulses, 300 ms apart.

See the communication protocol manual for a detailed description of the DNP3 protocol

10.8.3

Setting guidelines

SEMOD158639-5 v3

AUTOBITS function block has one setting, (

Operation: Enabled/Disabled) enabling or disabling the

function. These names will be seen in the DNP communication configuration tool in PCM600.

1MRK 505 287-UUS B

Section 10

Control

Busbar protection REB650

177

Application manual

Содержание RELION 650 SERIES






































































































































































































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды

ABB RELION 650 SERIES, Руководство по применению

Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды