ABB RELION 650 SERIES Скачать руководство пользователя страница 217

Страница: 217 / 262

Section 13

Metering

13.1

Pulse counter PCGGIO

13.1.1

Identification

GUID-50478353-2EE5-45ED-8A89-4EB0A0F71314 v2

Function description

IEC 61850

identification

IEC 60617

identification

ANSI/IEEE C37.2

device number

Pulse counter

PCGGIO

S00947 V1 EN-US

13.1.2

Application

M13395-3 v5

Pulse counter (PCGGIO) function counts externally generated binary pulses, for instance pulses

coming from an external energy meter, for calculation of energy consumption values. The pulses

are captured by the binary input module (BIO), and read by the PCGGIO function. The number of

pulses in the counter is then reported via the station bus to the substation automation system or

read via the station monitoring system as a service value. When using IEC 61850–8–1, a scaled

service value is available over the station bus.

The normal use for this function is the counting of energy pulses from external energy meters. An

optional number of inputs from the binary input module in IED can be used for this purpose with a

frequency of up to 10 Hz. PCGGIO can also be used as a general purpose counter.

13.1.3

Setting guidelines

M13396-4 v5

From PCM600, these parameters can be set individually for each pulse counter:

•

Operation: Disabled/Enabled

•

tReporting: 0-3600s

•

EventMask: NoEvents/ReportEvents

The configuration of the inputs and outputs of PCGGIO function block is made with PCM600.

On the binary input output module (BIO), the debounce filter default time is set to 5 ms, that is,

the counter suppresses pulses with a pulse length less than 5 ms. The binary input channels on the

binary input output module (BIO) have individual settings for debounce time, oscillation count and

oscillation time. The values can be changed in the local HMI and PCM600 under Main menu/

Configuration/I/O modules

The debunce time should be set to the same value for all channels on the board

1MRK 505 287-UUS B

Section 13

Metering

Busbar protection REB650

211

Application manual

Содержание RELION 650 SERIES






































































































































































































































































Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды

ABB RELION 650 SERIES, Руководство по применению

Результаты поиска

Содержание RELION 650 SERIES

Отзывы:

Бренды по названию

Популярные бренды