ABB Relion 611 Series Скачать руководство пользователя страница 79

Страница: 79 / 108

Section 7

IEC 61850 communication engineering

7.1

IEC 61850 protocol references and pre-conditions

To engineer the IEC 61850 protocol interface for the protection relay, the following
additional manuals or knowledge of their contents is required.

•

Knowledge of the IEC 61850 engineering process as described in the IEC 61850
standard

•

The technical manual describes the function blocks defined as logical nodes

•

The IEC 61850 engineering guide

•

The IEC 61850 conformance documents for the protection relay to be engineered

•

The IEC 61850 parameter list

7.2

IEC 61850 interface

For more information on the implementation of IEC 61850 in
protection relays, see IEC 61850 engineering guide and conformance
documents.

Table 9:

Function blocks and IEC 61850 Edition 1 and Edition 2 Logical Nodes

Function

IEC 61850

Logical device

Logical nodes in

Ver.2.0

Logical nodes in

Ver.1.0

Protection
Three-phase non-directional overcurrent protection, low

stage

PHLPTOC

LD0

PHLPTOC

Three-phase non-directional overcurrent protection, high

stage

PHHPTOC

LD0

PHHPTOC

Three-phase non-directional overcurrent protection,

instantaneous stage

PHIPTOC

LD0

PHIPTOC

Non-directional earth-fault protection, low stage

EFLPTOC

LD0

EFLPTOC

Non-directional earth-fault protection, high stage

EFHPTOC

LD0

EFHPTOC

Non-directional earth-fault protection, instantaneous stage EFIPTOC

LD0

EFIPTOC

Three-phase directional overcurrent protection, low stage

DPHLPDOC

LD0

DPHLPTOC

DPHLRDIR

DPHLPTOC

DPHLRDIR

Three-phase directional overcurrent protection, high stage DPHHPDOC

LD0

DPHHPTOC

DPHHRDIR

DPHHPTOC

DPHHRDIR

Directional earth-fault protection, low stage

DEFLPDEF

LD0

DEFLPTOC

DEFLRDIR

DEFLPTOC

DEFLRDIR

Table continues on next page

1MRS241255 B

Section 7

IEC 61850 communication engineering

611 series

Engineering Manual

Содержание Relion 611 Series












































































































Результаты поиска

Содержание Relion 611 Series

Отзывы:

Бренды по названию

Популярные бренды

ABB Relion 611 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Relion 611 Series

Отзывы:

Бренды по названию

Популярные бренды