ABB MO132 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 80

ABB MO132 Скачать руководство пользователя страница 24

MANUAL MOTOR STARTER GUIDE

APRIL 19

24/80

2.4.6 Accessories and enclosures

Since manual motor starters combine the functions of multiple components, such as circuit-breakers, disconnect
switches, and overload relays, they are offered with many of the same types of accessories. Thus, the manual motor
starters can be extended with auxiliary contacts which can be connected either on the side or - especially to save
space - on the front. Also, undervoltage releases are available, and shunt releases complement the product range.
With the help of separately available adapters can the manual motor starter easily and quickly, build to a compact
starter combinations of motor protection switch and contactor.

Signaling and
status indica-
tion

Auxiliary contacts

HK1, HKF1

Signal contact alarms

SK1

Short-circuit signaling contact

CK1

Increasing
functionality

Undervoltage releases

UA1

Shunt trips

AA1

Current limiters

S803W

Reducing in-
stallation time
and saving
space

Three-phase busbar

PSx

Feeder (in-feed) terminal blocks

S1-Mx

Connecting Link

BEA

External oper-
ation and
enclosures

Handles and shafts, NEMA Types 1, 3R, 12

Shaft alignment accessories

Door-mount kits, NEMA Type 12

DMS132

Enclosures, NEMA Type 12

IB132

Auxiliary and signaling contacts can be combined to provide external status indication for a variety of conditions and
states. The table below shows an overview of the functionality of these contact types.

Contact type

Condition / state of manual motor starter

OFF

ON

Signaling

contact

Short-cir-

cuit trip

Undervolt-

age

release

Shunt trip

HK1,

HKF1

Auxiliary

contacts

Change posi-

tion with the

main contacts

Normally-

open

O

X

O

O

O

O

Normally-

closed

X

O

X

X

X

X

SK1

Signal con-

tact alarms

Signals trip-

ping by short-

circuit or over-

load

Normally-

open

O

O

X

X

X

X

Normally-

closed

X

X

O

O

O

O

CK1

Short-circuit

indicators

Signals trip-

ping by short-

circuit

Normally-

open

O

O

O

X

O

O

Normally-

closed

X

X

X

O

X

X

O = Open; X = Closed

Table 9: Condition / state of manual motor starter.

«
...
22
23
24
25
26
...
»

Содержание MO132

















































































Отзывы:

Нет отзывов