manualshive.com logo in svg

ABB ESI-S, Инструкции по установке, эксплуатации и обслуживанию

Поделиться
Скачать
ABB ESI-S Скачать руководство пользователя страница 67

Manual Energy Storage Inverter ESI-S

 Electrical design and installation 67

6.14 Electrical connections of inverter options and accessories

Inverter options must be ordered in advance and are cabled in the factory. For these
options, refer to the wiring diagram provided with your inverter to identify the electrical
connections if desired. For some accessories however, the customer may have to do the
cabling on site. These accessories include:

−

The  connection  of  the  USB  or  Ethernet  cable  used  for  PQF-Link  software
communication (optional)

−

The connection of the Ethernet cable used for Modbus TCP communication
(optional)

−

The connection of the RS485 Modbus RTU adapter (optional)

The connections of the aforementioned accessories are discussed next.

WARNING: Before cabling any of the circuits discussed below, switch off the power
supply to the inverter. When the inverter has already been installed on site, this must
be done by opening the protection system located just upstream of the inverter and
opening the auxiliary fuse box present in the inverter. Wait for at least 25 minutes to
allow for the DC capacitors to discharge when the inverter has been connected to the
network before. Failure to do so may result in lethal injury or death.

6.14.1 External communication with ESI

The ESI Inverter communicates with a computer in three possible ways:

−

Using our in-house communication software called PQF-Link (rs232)

−

Using any communication system supporting the Modbus TCP protocol

−

Using any communication system supporting the Modbus RTU protocol

For communication over Modbus TCP, the computer can be connected through the
Ethernet port using standard cable (RJ45).

For communication over Modbus RTU, we need a RS485 Modbus adapter (as shown in

Figure 67

). This adapter has to be connected to the rear side of the ESI-Manager. This is

done by inserting the adapter plug firmly in the dedicated socket.

Figure 67

shows the

location at the rear of the ESI-Manager where the plug has to be inserted. The user can
use custom software where the standard Modbus RTU protocol is implemented or any
other standard software (OPC server, SCADA …).

Содержание ESI-S









































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды