ABB CPTC-02 Скачать руководство пользователя

Страница: 38 / 78

Note:

Only frames R0…R5 need CPTC-02 to be supplied by an

external power supply, frames R6…R9 have corresponding terminals
40 and 41 on the control unit.

Description

Marking

External 24 V (AC/DC) input

24V AC/DC +
in

External 24 V (AC/DC) input

24V AC/DC - in

PTC sensor input

For the recommended cable type and correct tightening torque, see
the technical data.

To enable the SMT function, connect the PTC sensor to the PTC IN
input.

To disable the SMT function, connect a resistor (100 ohm … 1 kohm
¼ W wire-wound) to the PTC IN input.

Note:

If you do not connect a PTC sensor or resistor to the PTC IN

input, the STO function stays active. You cannot start the motor while
the STO function is active.

Wiring examples

Connect the external control cables to the applicable module
terminals. Ground the outer shield of the cables 360 degrees under
a grounding clamp on the grounding shelf of the control cables.

38 Electrical installation

Содержание CPTC-02














































































Результаты поиска

Содержание CPTC-02

Отзывы:

Похожие инструкции для CPTC-02

Бренды по названию

Популярные бренды

ABB CPTC-02, Руководство пользователя

Результаты поиска

Содержание CPTC-02

Отзывы:

Похожие инструкции для CPTC-02

Бренды по названию

Популярные бренды