ABB CPTC-02 Скачать руководство пользователя

Страница: 37 / 78

3. Install the drive, including the components of the ATEX-certified

motor thermal protection function, outside the potentially explosive
atmosphere.

4. For the sensor connection, ABB recommends to use shielded

twisted-pair cable. This type of cable decreases electromagnetic
interference in the sensor circuit.

5. Route the sensor cables away from the motor cable. Power cables

can cause electromagnetic interference in the sensor circuit.

6. Ground all sensor cable shields to a single grounding point

outside the potentially explosive atmosphere. 360-degree
grounding of the cable shields at the cable entry of the drive is
recommended. Do not connect the cable shields to ground at the
sensor end of the cable.

Terminal designations

￭

Motor thermistor connection

Description

Marking

PTC connection

PTC IN

Ground (earth) potential

PTC IN

￭

Relay output connection

Description

Marking

Common, C

RO PTC C

Normally open, NO

RO PTC C

￭

External power supply

The external power supply is needed only if you want to connect an
external back-up power supply for the drive control unit.

Electrical installation 37

Содержание CPTC-02














































































Результаты поиска

Содержание CPTC-02

Отзывы:

Похожие инструкции для CPTC-02

Бренды по названию

Популярные бренды

ABB CPTC-02, Руководство пользователя

Результаты поиска

Содержание CPTC-02

Отзывы:

Похожие инструкции для CPTC-02

Бренды по названию

Популярные бренды