ABB A175-M66 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 150

background image

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.12 Hazards during operation and maintenance

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

WARNING

Hot surfaces on a non-insulated turbocharger

Non-insulated turbochargers can cause serious injuries to personnel (burns).

The turbocharger is supplied with or without insulation in accordance with
the purchase order received from the enginebuilder. If supply is without in-
sulation, the enginebuilder is responsible for providing the turbocharger
with proper insulation and for providing protection against contact with hot
surfaces.

u

Compliance with the instructions and specifications given by the en-
ginebuilder to protect against hot turbocharger surfaces is compulsory.

Wear safety gloves to protect against thermal hazards.

Hazards due to rotating parts

WARNING

Hazards due to rotating parts

Contact with rotating parts can cause severe injury. The turbocharger is
never allowed to be operated without filter silencer or air-inlet casing. With
the engine stopped, the rotor can rotate due to the stack draught alone.

u

Operate the turbocharger in compliance with the specifications.

u

Secure the rotor against unintentional rotation during maintenance.

Wear safety gloves to protect against mechanical hazards.

Page

22

/

147

«
...
22
23
24
25
26
...
»

Содержание A175-M66























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A175-M66

Бренд: Saito Страницы: 2

Бренд: Habasit Страницы: 54

Бренд: ULPOWER Страницы: 25

Бренд: B&S Страницы: 26

Бренд: Nissei Страницы: 16

Бренд: dunkermotoren Страницы: 32

PowerLine TG500B

Бренд: Texas Страницы: 98

Бренд: Mercedes-Benz Страницы: 324

Бренд: Harmonic Drive Страницы: 48

Бренд: Volvo Penta Страницы: 122

Бренд: Volvo Страницы: 8

Бренд: Seva-tec Страницы: 20

Бренд: DANA Страницы: 4

MAX-32SX-H Series

Бренд: O.S. engine Страницы: 32

Бренд: Honda Страницы: 96

Бренд: Honda Страницы: 114

Car Engine GX340

Бренд: Honda Страницы: 96

Бренд: Chevrolet Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды