ABB A175-M66 Скачать руководство пользователя страница 41

Страница: 41 / 150

Operation Manual / A170-M.. - A175-M..

4 Commissioning / 4.2 Inspection procedures

HZTL4033_EN

Rev.H

July 2021

4.2

Inspection procedures

4.2.1

Introduction

Inspection procedures include preventative visual controls, monitoring and measuring work
before and during commissioning. Inspection procedures enable changes to the turbochar-
ger to be detected. Machine damage can be prevented.

4.2.2

Checks before commissioning

Filter mat (if available)

Check for damage and contamination.

Lubricating system

CAUTION

Contaminated oil

Serious damage to engine or property can be caused by dirt and solid ma-
terial particles in the oil.

For the initial commissioning phase and after all service work, flush the
complete lubricating system with warm oil.

Use special running-in filters when running in the engine and after all ser-
vice work on the lubricating system.

Check that the oil filter is clean before commissioning.

Check the oil pressure in the oil supply pipes.

4.2.3

Checks after commissioning (engine in idle mode)

Lubricating system

Check the oil pressure in the oil supply pipes.

Check oil inlet temperature.

The admissible values are specified in section Oil supply.

Gas, air and oil pipes

After starting the engine, check all gas, air and oil pipes for leaks.

Page

147

Содержание A175-M66





















































































































































Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды

ABB A175-M66, Руководство по эксплуатации

Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды