ABB A175-M66 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 150

background image

Operation Manual / A170-M.. - A175-M..

7 Periodic maintenance / 7.2 Cleaning the filter silencer

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

Cleaning the absorption segments

(see Fig. 26: Cleaning the filter silencer

u

Loosen and remove lock nuts (81273).

u

Loosen and remove screws (81272) to the connecting rods (81269).

u

Remove connecting rods (81269).

u

Remove and clean cover grid (81266).

u

Pull out insert units (E), bend up sheet-metal coverings (81137) and take out absorption
segments (81136).

u

Clean the absorption segments (81136).
When cleaning, make sure that the absorption segments (81136) are only cleaned lightly
with pressurized air, a soft brush or with damp cleaning cloths.

u

Have any heavily contaminated absorption segments and filter rings as well as damaged
connecting rods replaced by an ABB Turbocharging Service Station.

Fitting the cover grids and absorption segments

(see Fig. 26: Cleaning the filter silencer

CAUTION

Penetration of dirt and foreign particles

Any penetration of dirt and foreign particles into the compressor can dam-
age it.

u

Fit the connecting rods (81269) correctly in the slots on the filter silencer
body (81135).

u

It must not be possible to rotate or move the cover grid (81266) after as-
sembly.

u

Check the position and alignment of the connecting rods during and after
assembly.

u

Assemble the insert units (E) by inserting the absorption segments (81136) into the
sheet-metal coverings (81137).

u

Bend the sheet-metal coverings (81137) back into the original shape.

u

Insert the insert units (E) into the slotted guides in the filter silencer body (81135).

If a cleaning container is attached to the filter silencer (option, depending on turbocharger),
the water injection pipe must now be reinstalled.

u

Position the cover grids (81266) evenly and in the correct position.

Page

55

/

147

«
...
55
56
57
58
59
...
»

Содержание A175-M66























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A175-M66

Бренд: O.S. engine Страницы: 19

Бренд: Kohler Страницы: 108

Бренд: Westerbeke Страницы: 60

Бренд: Farymann Diesel Страницы: 34

MaxxForce DT 10

Бренд: Navistar Страницы: 109

Бренд: Amico Страницы: 47

Lombardini LGW 523 MPI

Бренд: Kohler Страницы: 144

Бренд: Siemens Страницы: 50

Worm Gearbox S 5 BA 2012

Бренд: Siemens Страницы: 54

SINAMICS S120 1PM4

Бренд: Siemens Страницы: 100

SIMOTICS-T 1FW6 Series

Бренд: Siemens Страницы: 106

SIMOTICS XP 1MD4

Бренд: Siemens Страницы: 128

SIMOTICS TN 1LL8

Бренд: Siemens Страницы: 148

SIMOTICS XP 1MB155

Бренд: Siemens Страницы: 152

SIMOTICS XP 1MB5 SH400

Бренд: Siemens Страницы: 166

Бренд: Siemens Страницы: 170

SIMOTICS XP 1LA5

Бренд: Siemens Страницы: 174

SIMOTICS-T 1FW68

Бренд: Siemens Страницы: 180

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды