ABB A175-M66 Скачать руководство пользователя страница 105

Страница: 105 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.10 Fitting the spinner nose cone

HZTL4033_EN

Rev.H

July 2021

2. Clean and degrease the inner thread of the threaded stud and socket screw (25013).

3. Coat the outer contact surface (A) between the spinner nose cone and the compressor

wheel over its entire circumference with Molykote® TP42.

4. Apply Loctite® 542 to the inner thread of the threaded stud.

Fig. 59: Fitting the spinner nose cone (25012)

Product

Size

Tightening torque [Nm]

A170-M

A175-M

M10

Table 43: Tightening torque (25013)

Always use a new socket screw (25013) and washer (25014) from the customer spare part set
(97070).

5. Fit the spinner nose cone and secure with washer (25014) and socket screw (25013). Ob-

serve tightening torque. The following must be taken into account:

The tightening torque must be applied by two people. One person tightens socket
screw (25013), while the second person holds the compressor wheel (25000).

Apply tightening torque constantly, avoid jerky movements. Observe tightening torque.

Do not repeat the tightening of socket screw (25013).

6. Measure and note down distance Z between spinner nose cone and compressor wheel at

no less than three points around the circumference.

Permissible distance Z:

0.1 – 0.7 mm

Permissible difference of the measurements:

± 0.1 mm

Page

103

147

Содержание A175-M66





















































































































































Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды

ABB A175-M66, Руководство по эксплуатации

Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды