ABB A175-M66 Скачать руководство пользователя страница 47

Страница: 47 / 150

Operation Manual / A170-M.. - A175-M..

5 Monitoring during operation / 5.2 Turbocharger speed

HZTL4033_EN

Rev.H

July 2021

5.2.4

Replacing the speed sensor

WARNING

Hot cable connector and hot speed sensor

Danger of burns. The cable connector and speed sensor can reach temperat-
ures in excess of 100 °C during operation.

When disassembling the cable connector and speed sensor, wear safety
gloves.

Wear safety gloves to protect against thermal hazards.

Reduce the engine performance to idling and then stop the engine. Pay attention to post-
lubrication (

Stopping the engine

→

Switch off the lubricating oil supply to the turbocharger.

Disconnect the cable connector from the speed sensor.

Screw out defective speed sensor.

Screw in new speed sensor to the stop.

The speed sensor is designed with a sealing lip and does not require any additional gasket
for assembly.

Connect cable connector (86515) with the speed sensor (86505)

Switch on lubricating oil supply to the turbocharger.

5.2.5

Malfunction of the speed measurement system

The possible reasons for malfunction of the speed measurement system are described in
chapter Troubleshooting (Reasons for malfunction of the speed sensor).

Page

147

Содержание A175-M66





















































































































































Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды

ABB A175-M66, Руководство по эксплуатации

Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды