ABB A175-M66 Скачать руководство пользователя страница 4

Страница: 4 / 150

Operation Manual / A170-M.. - A175-M..

Table of contents

HZTL4033_EN

Rev.H

July 2021

Stopping the engine................................................................................................... 52

Periodic maintenance.......................................................................................... 53

7.1

Foreword to maintenance......................................................................................... 53

7.2

Cleaning the filter silencer ........................................................................................ 54

7.3

Cleaning the slotted diffuser..................................................................................... 57

7.4

Cleaning the compressor during operation .......................................................... 58

7.5

Cleaning turbine and nozzle ring ............................................................................. 64

Troubleshooting................................................................................................... 70

8.1

Malfunctions when starting...................................................................................... 70

8.2

Malfunctions during operation ................................................................................. 71

8.3

Surging of the turbocharger...................................................................................... 73

8.4

Malfunctions when stopping.................................................................................... 74

8.5

Speed measurement system ..................................................................................... 75

Disassembly and assembly................................................................................. 76

9.1

Introduction ................................................................................................................. 76

9.2

Weight of assemblies................................................................................................. 78

9.3

Removing the air inlets .............................................................................................. 79

9.4

Axial clearance A prior to disassembly .................................................................... 81

9.5

Removing the compressor casing ........................................................................... 82

9.6

Removing the cartridge group ................................................................................. 86

9.7

Removing the nozzle ring .......................................................................................... 89

9.8

Installing the nozzle ring ........................................................................................... 94

9.9

Installing the cartridge group .................................................................................. 99

9.10

Fitting the spinner nose cone ................................................................................ 102

9.11

Installing the compressor casing .......................................................................... 104

9.12

Axial clearance A after assembly............................................................................ 108

9.13

Installing the air inlets ............................................................................................. 109

9.14

Removing and installing turbine-end nozzle ring................................................ 112

9.15

Table of tightening torques..................................................................................... 116

Taking a turbocharger out of operation......................................................... 119

10.1

Possible emergency repairs..................................................................................... 119

10.2

Locking the rotor ...................................................................................................... 120

10.3

Fitting the cover plate............................................................................................... 123

10.4

Blanking off the inlets and outlets ......................................................................... 125

10.5

Engines with bypass around the turbocharger ................................................... 125

Mothballing the turbocharger.......................................................................... 126

11.1

Taking the engine out of operation for up to 12 months .................................. 126

11.2

Taking the engine out of operation for more than 12 months ......................... 127

Material and Disposal........................................................................................ 128

12.1

REACH and RoHS Compliance Declaration For Products .................................. 128

12.2

Disposing of turbocharger components .............................................................. 129

Содержание A175-M66





















































































































































Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды

ABB A175-M66, Руководство по эксплуатации

Результаты поиска

Содержание A175-M66

Отзывы:

Похожие инструкции для A175-M66

Бренды по названию

Популярные бренды