ABB A170-M62 Скачать руководство пользователя

Страница: 146 / 150

Operation Manual / A170-M.. - A175-M..

Figures

HZTL4033_EN

Revision H

July 2021

Figures

Fig. 1: Serial number (01) on the rating plate ........... 4

Fig. 2: Layout and function........................................... 6

Fig. 3: Connection of the compressor wheel cooling ... 7

Fig. 4:

olatile

orrosion

nhibitor (VCI)................... 10

Fig. 5: Package with hygrometer................................ 11

Fig. 6: Warning plates on the turbocharger ............. 16

Fig. 7: Rating plate ........................................................ 17

Fig. 8: Locations of the rating plates ........................ 18

Fig. 9: Attachment of loads on the crane hook ....... 19

Fig. 10: Attachment angle............................................ 19

Fig. 11: Turbocharger suspension points ................ 28

Fig. 12: Turbocharger suspension points ................ 29

Fig. 13: Removing the foot mounting....................... 30

Fig. 14: Loosening the clamping nut ......................... 31

Fig. 15: Turbocharger suspension points ................. 32

Fig. 16: Removing auxiliary screw .............................. 33

Fig. 17: Compressor-end foot ..................................... 33

Fig. 18: Turbine-end foot ............................................ 34

Fig. 19: CE foot contact surface ................................ 35

Fig. 20: TE foot: Handling of cup spring contact sur-
face / foot contact surface ........................................ 35

Fig. 21: Tightening the foot screws (1)..................... 36

Fig. 22: Tightening procedure..................................... 37

Fig. 23: Lubricating oil pressure measuring point.. 41

Fig. 24: Speed measurement ..................................... 43

Fig. 25: Noise insulation, bellows .............................. 47

Fig. 26: Cleaning the filter silencer............................ 54

Fig. 27: Cleaning the filter silencer (2) ...................... 56

Fig. 28: Cleaning the slotted diffuser........................ 57

Fig. 29: Operation of water pressure vessel ........... 62

Fig. 30: Turbine and nozzle ring cleaning cycle ...... 66

Fig. 31: Cleaning cycle of turbine and nozzle ring
with load ramp.............................................................. 67

Fig. 32: Procedure Wet cleaning of turbine and
nozzle ring ....................................................................... 68

Fig. 33: Weight of assemblies ..................................... 78

Fig. 34: Removing the filter silencer .......................... 79

Fig. 35: Removing the air suction branch ................. 80

Fig. 36: Axial clearance.................................................. 81

Fig. 37: Removing wall insert ....................................... 82

Fig. 38: Transporting and turning wall insert .......... 83

Fig. 39: Removing the diffuser .................................... 84

Fig. 40: Removing the compressor casing ............... 85

Fig. 41: Safety-relevant screws ................................... 86

Fig. 42: Removing cartridge group 1.......................... 87

Fig. 43: Removing cartridge group 2 ......................... 88

Fig. 44: Removing turbine diffuser 1.......................... 89

Fig. 45: Removing turbine diffuser 2 ......................... 90

Fig. 46: Removing cover ring 1 .................................... 91

Fig. 47: Removing cover ring 2 .................................... 92

Fig. 48: Removing nozzle ring 1................................... 92

Fig. 49: Removing nozzle ring 2 .................................. 93

Fig. 50: Installing nozzle ring 1 .................................... 94

Fig. 51: Installing nozzle ring 2 .................................... 95

Fig. 52: Installing cover ring......................................... 96

Fig. 53: Installing turbine diffuser 1 ........................... 97

Fig. 54: Installing turbine diffuser 2........................... 98

Fig. 55: Installing the cartridge group 1 .................... 99

Fig. 56: Installing the cartridge group 2.................. 100

Fig. 57: Installing the cartridge group 3 .................. 100

Fig. 58: Preparing the threaded stud (25008) ....... 102

Fig. 59: Fitting the spinner nose cone (25012)....... 103

Fig. 60: Installing the compressor casing............... 104

Fig. 61: Installing diffuser........................................... 105

Fig. 62: Turning and moving in wall insert.............. 106

Fig. 63: Fitting wall insert........................................... 107

Fig. 64: Axial clearance ............................................... 108

Page

144

147

Page

144

147

Содержание A170-M62





















































































































































Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды

ABB A170-M62, Руководство по эксплуатации

Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды