ABB A170-M62 Скачать руководство пользователя | Manualshive

Страница: 28 / 150

background image

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.14 Safe maintenance

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

Safety when taking out of operation or preparing for mothballing

u

Observe the material safety data sheet for the cleaning and mothballing agents.

u

Wear personal protective equipment (PPE) according to the material safety data sheet.

Mechanical hazards when working on the turbocharger

WARNING

Mechanical hazard

Severe injuries to personnel or fatal accidents can be caused by mechanical
influences as a consequence of hazardous and inadequate operational pro-
cedures.

u

Observe the general rules for occupational safety and prevention of acci-
dents.

u

Ensure workplace safety.

u

Only perform operations that are described in this chapter.

u

Only perform operations for which you have previously received instruc-
tion or training.

Hazards due to operating materials and supplies

Operating materials and supplies are substances required for the operation of the tur-
bocharger or for the performance of maintenance work. Oils, greases, coolants, detergents
and solvents, acids and similar substances can be classified as hazardous substances.

WARNING

Handling operating materials and supplies

Swallowing or inhaling vapours of operating materials and supplies or con-
tact with them may be harmful to health.

u

Do not breathe in these substances and avoid contact with the skin.

u

Ensure proper ventilation.

u

Observe the information in the material safety data sheet for the operat-
ing materials and supplies.

u

Wear personal protective equipment (PPE) according to the material
safety data sheet.

u

Comply with local legislation.

Wear safety goggles.

Wear safety gloves to protect against chemical hazards.

Wear a respiratory mask to protect against gases.

Page

26

/

147

«
...
26
27
28
29
30
...
»

Содержание A170-M62























































































































































Отзывы:

Нет отзывов

Похожие инструкции для A170-M62

Бренд: Hacker Страницы: 8

Бренд: Kärcher Страницы: 224

Бренд: O.S. engine Страницы: 19

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Crankcase for Harley-Davidson

Бренд: S&S Cycle Страницы: 12

Бренд: Polini Страницы: 34

Бренд: YOODA Страницы: 7

Бренд: CAB Страницы: 16

Бренд: O.S. engine Страницы: 4

Бренд: MINN KOTA Страницы: 42

Бренд: Stark Страницы: 14

Бренд: Vetus Страницы: 28

Бренд: SUHNER Страницы: 16

Бренд: Kohler Страницы: 108

Бренд: Metronic Страницы: 24

Enduro RR 350 2015

Бренд: Beta Страницы: 158

Бренд: Magnum Страницы: 7

Бренд: Yanmar Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды