ABB A170-M62 Скачать руководство пользователя

Страница: 46 / 150

Operation Manual / A170-M.. - A175-M..

5 Monitoring during operation / 5.2 Turbocharger speed

HZTL4033_EN

Rev.H

July 2021

5.2.3

Speed differences with several turbochargers per engine

The speeds of all turbochargers on an engine vary only slightly from each other in standard
operation.

The difference between the highest and the lowest turbocharger speed must not be more
than 3 %, relative to the speed limit n

Bmax

If this permissible range of difference is exceeded, the following steps must be carried out:

Reduce the engine performance immediately to the point at which the maximum tur-
bocharger speed does not exceed 70 % of n

Bmax

If the engine cannot be stopped, it can continue to be driven at this reduced engine load
or turbocharger speed.

If a turbocharger surges continuously, the engine performance must be reduced further.

Measure the temperatures in the air lines and gas piping from and to the turbochargers
and compare with normal values. If clear deviations of temperature are found, the nearest
ABB Turbocharging Service Station has to be contacted.

Check the pressure loss of the alternative air inlet and compare it with normal values.

If the engine can be stopped temporarily:

Inspect air lines, gas piping and the turbochargers and remedy any malfunctions.

In any case, contacting the nearest ABB Turbocharging Service Station is recommended.

Page

147

Содержание A170-M62





















































































































































Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды

ABB A170-M62, Руководство по эксплуатации

Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды