ABB A170-M62 Скачать руководство пользователя

Страница: 29 / 150

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.14 Safe maintenance

HZTL4033_EN

Rev.H

July 2021

WARNING

Danger of fire or explosion

Flammable and combustible operating materials and supplies can catch fire
or resulting vapours can lead to an explosion.

Observe the information in the material safety data sheet for the operat-
ing materials and supplies.

Comply with local legislation.

Do not allow any exposed flame or ignition source during cleaning work.

Carry out cleaning in the open or provide sufficient ventilation.

CAUTION

Environmental hazard

Improper handling of operating materials and supplies can lead to environ-
mental damage.

Observe the information in the material safety data sheet for the operat-
ing materials and supplies.

Comply with local legislation.

Hazards due to the handling of insulation materials

WARNING

Danger from insulation materials

Dust or fibres from insulation materials can have adverse effects on the
health or cause irritations. Unsuitable and combustible insulation materials
are a fire hazard.

Only use suitable and non-combustible insulation materials.

Ensure good ventilation at the workplace.

Avoid whirling up dust.

Use dust-free tools and working methods.

Remove package at the workplace only.

Proceed with particular care when removing old insulation materials.

Dispose of insulation materials properly and in an environmentally com-
patible manner in compliance with the legal regulations.

Wear safety goggles.

Wear a respiratory mask to protect against dusts.

Wear safety gloves to protect against chemical hazards.

Page

147

Содержание A170-M62





















































































































































Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды

ABB A170-M62, Руководство по эксплуатации

Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды