ABB A170-M62 страница 18 Скачать руководство пользователя

Страница: 18 / 150

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.8 Warning plates on the turbocharger

HZTL4033_EN

Rev.H

July 2021

2.8

Warning plates on the turbocharger

Warning plates are affixed at the following locations:

Fig. 6: Warning plates on the turbocharger

If warning plates are not present in the designated locations or not readable, proceed as fol-
lows:

Order new warning plates from ABB Turbocharging Service Stations.

Remove any warning plates that have become unreadable.

Clean and degrease the areas designated for the warning plates.

Fit new warning plates and remove protective sheets.

Turbochargers supplied to the enginebuilder without insulation must be equipped later with
warning plates on the insulation. This is the responsibility of the enginebuilder.

Page

147

Содержание A170-M62





















































































































































Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды

ABB A170-M62, Руководство по эксплуатации

Результаты поиска

Содержание A170-M62

Отзывы:

Похожие инструкции для A170-M62

Бренды по названию

Популярные бренды