background image

13

Engine oil and fuel

This product is equipped with a 4-stroke
engine. Before operation you have to add
proper engine oil and fuel.
1. Place the product on a stable, level
surface. We recommend laying a
nonflammable sheet underneath.
2. Use proper funnels. Avoid splitting and
overfilling the tanks.

WARNING!  Ensure  that  there
are  no  naked  flames  around
the product!  Do  not  smoke
while filling fuel and oil!

3. Always dispose fuel, used oil and
objects contaminated with them in
accordance with local regulations.

Engine oil

WARNING! This product is
not supplied with oil.
However, for manufacturing
reasons it is possible that
a small quantity may be

in the engine! Before operating this
product it is essential to fill it with
proper oil (see “product
specifications”)!

1. Unscrew and take out the oil tank cap.

2. Gradually add good-quality engine oil
(5W-30). Allow the oil to settle.
3. Check the oil level frequently while
filling. Wipe the oil dipstick clean; refit
and tighten the oil tank cap and then

remove it again. The oil level must be
between the “H (High)” and “L (Low)”
markings.

Do not overfill

.

4. Wipe spilled oil with a soft cloth and
screw up the oil tank cap.

Fuel

WARNING! This product is
not supplied with fuel!
Before operating this
product it is essential to fill
it with fuel!

1. Always use clean, fresh unleaded fuel.
Purchase fuel in quantities that can be
used within 30 days.
2. Never mix oil with fuel. Avoid getting
dirt, dust or water in the fuel tank.
3. Unscrew the fuel tank cap.
4. Wipe any spilled fuel with a soft cloth
and screw the fuel tank cap.

NOTE: Fuel deteriorates over
time. It may be DIFFICULT to
start the engine if you use fuel
which has been kept for more

than 30 days. Towards the end of the
season, it is advisable to put only as
much fuel in the tank as you need for
each use, since it should be completely
used up before storing the product.
Empty remaining fuel from the tank and
the CARBURETTOR when storing the
product for over 30 days.

Содержание AGT1424S


































Отзывы: