A&D RA3100 Omniace Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 76

A&D RA3100 Omniace Скачать руководство пользователя страница 67

8.Specifications -8.2.Functional Specifications

1WMPD4004445

67

8.2.6. Monitor Function

Item

Specifications

Display screen

MEASURE
PLAYBACK

Displays the state waveform of the input signal
Playback the memory, SSD, or printer recorded data

Waveform type

Y-T waveform, X-Y waveform, FFT waveform
Enables waveform display for an arbitrary analog signal and logic signal
Y-T waveform
X-Y waveform
FFT waveform

Enables 48 channel/sheet signal display
Enables a maximum of four X-Y waveform sets to be displayed
Enables FFT analysis results to be displayed for a maximum of
two channels

Y-T waveform
display

Display width

20 div x 20 div
Time axis (T axis)
Amplitude axis (Y axis)
Display area

1 div = 100 samples
1 div = 1/10 RANGE (with display range at 100%)
Specifies the display position, display range, display maximum,
and display minimum

Sheet

Enables waveform screens to be managed as three waveform screens (display channel
sets)

Display functions Numeric value display

Scale
Grid
Trigger/mark
Cursor

Pen position
Zero position
Time display
Pinch in/out

Numeric value display of input signal
Scale display of amplitude axis
Grid display of waveform area
Displays detected trigger/mark
Displays two cursors
Displays the signal information (position and value) of the
cursors, information on the differences between cursors,
maximums, minimums, and averages
Displays the signal amplitude position
Displays the signal zero position
Displays the time on the bottom of the display area
Enlarges/reduces the display waveform

TRIG.SYNC

Updates the waveform display screen when the trigger conditions are established

8.2.7. X-Y Waveform

Item

Specifications

Data selection

SSD recorded data

Data format: Normal data

X-Y axis

X axis channel:
Y axis channel:

User-defined analog channel
User-defined analog channel
Four waveforms can be set

Sampling speed 1 kS/s (max)

Display format

Select single screen or
quad screen
Single
Quad

Displays four sets of X-Y waveforms on a single screen
Displays a separate X-Y waveform on each of four screens

«
...
65
66
67
68
69
...
»

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды