A&D RA3100 Omniace Скачать руководство пользователя страница 18

Страница: 18 / 76

1.Name and Function of Each Block - 1.5.Screen and Setup Menu

1WMPD4004445

1.5.1. Side menu

(1) Time:

Displays the current time

(2) MEASURE/PLAYBACK: Switches the displayed waveform

MEASURE: Displays the current input waveform.

PLAYBACK: Displays the playback waveform of saved data.

(3) Waveform display area:

Select waveform recording device to display

Displays the recorded waveform for PRINTER/SSD/MEMORY.

(4) PAUSE:

Pauses the waveform displayed on the input monitor.

(5) TRIG.SYNC: Updates the input waveform display of a memory recording by

synchronizing it with a trigger.

(6) CH:

The input channel setup

Opens the channel setup sub menu to configure the channel setup,

input digital display, and trigger setup.

(7) SETUP:

Opens the setup menu to configure the detailed settings of the product.

Recording setup

(Recording/Channel list/Sheet/Printer)

Main unit setup

(Record management/Image

management/Environment/ Display)

Other setup

(Maintenance/Operation history/Version

management)

(8) SSD:

Displays the remaining space on the internal SSD. An error is displayed

when the remaining space is low.

(9) PAPER:

Displays the remaining amount of recording paper in the printer block.

An error is displayed when the remaining amount of recording paper is

low. Press and hold this key to initialize the recording paper type (roll

paper or Z-fold paper) and usage amount. When replacing the

recording paper, press and hold this key to initialize the remaining

amount of recording paper.

(10) SD:

Lights when an SD memory card is inserted in the SD card slot and

recognized as external memory.

(11) USB:

Lights when a USB stick is inserted in the USB port and recognized as

external memory.

(12) KEY:

Lights when the KEY LOCK switch on the side of the main unit is set to

on to disable the operation panel keys.

(13) SCREEN:

Lights when the SCREEN LOCK switch on the side of the main unit is

set to on to disable the display touch panel.

Содержание RA3100 Omniace













































































Результаты поиска

Содержание RA3100 Omniace

Отзывы:

Бренды по названию

Популярные бренды

A&D RA3100 Omniace, Простое руководство пользователя

Результаты поиска

Содержание RA3100 Omniace

Отзывы:

Бренды по названию

Популярные бренды