manualshive.com logo in svg

A&D RA3100 Omniace, Простое руководство пользователя

Поделиться
Скачать
A&D RA3100 Omniace Скачать руководство пользователя страница 5

 

To Safely Use Products 

1WMPD4004445 

5 

 

WARNING

 

Protective Grounding 

  Be sure to ground this product before supplying power. Grounding is necessary to use this product 

safely, as well as to protect the user and peripheral equipment from injury or damage. Be sure to 
observe the following instructions. 

  The AC power cable included with this product contains a ground lead. Connect the power cable into 

only a 3-pin AC outlet with a ground pole. 

  When grounding, do not connect the grounding lead to a water pipe, as water pipes are not 

necessarily conductive to the earth. Never connect the ground lead to a gas pipe either, as it is 
extremely dangerous. 

  While the power is supplied to the product, do not cut or remove the protective grounding line. 

Otherwise, safety of the product is not guaranteed. 

Overvoltage Category (Installation Category) 

  This product's Overvoltage Category is Category II. Do not use the product with higher categories, as 

connecting it to the line of a distribution board, etc. (CAT III) or the lead-in wire of a main power line 
(CAT IV) may lead to device failure. 

Measurement Category 

  The measurement input terminal Measurement Category of this product differs according to the 

installed modules.   
Use the product for measurement within the Measurement Category that meets the module 
specifications. Do not use it with a Measurement Category that exceeds the module specifications. 

Connection of Input Signals 

  Be sure to ground the grounding terminal of this product before connecting to the measurement 

target.   
Also, when connecting this product to another measurement instrument, be careful not to exceed the 
maximum allowable common mode input voltage range.   
A voltage exceeding the range can cause damage to this product. 

Use in Gaseous Atmosphere 

  Never use this product in a flammable or explosive atmosphere, or an atmosphere containing steam. 

Use in such atmosphere will result in danger to users and the product. 

Disassembling the Frame 

  It is dangerous to remove the frame of this product due to the high-voltage parts inside.   

The frame must not be removed from the product other than by our service engineers. 

Fuse at AC Power Supply Block 

  The fuse for this product cannot be replaced by the customer because it is located inside the main 

unit.   
Please contact our sales representative if the fuse may be blown. 

 

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды