A&D RA3100 Omniace Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 76

A&D RA3100 Omniace Скачать руководство пользователя страница 21

2.Pre-Measurement Procedures - 2.1.Before Switching On the Power

1WMPD4004445

21

2. Pre-Measurement Procedures

2.1. Before Switching On the Power

The preparations for using this product and the cautions are explained below.

2.1.1. Installation and Usage Environment

Use this product on a flat, level surface.
When using the printer, install it so that the recording
paper is level as indicated in the figure on the right.

CAUTION

Cautions Regarding the Installation Environment

Use this product at locations that satisfy the overvoltage requirement, the Category II (CAT II) of the

safety standard for electrical measurement instruments in EN61010-1.

This product has a Pollution Degree of 2.
Use this product in the following operating environments.

Operating temperature range: 0 to 40°C

Operating humidity range: 35 to 85% RH (without

condensation)

Do not use this product at the following locations. In addition, carefully check the environment when

using this product.

  Locations where the temperature and humidity rise due to direct sunlight or heaters
  Wet locations
  Locations where salt, oil, or corrosive gases exist
  Dusty locations
  Locations subject to strong vibrations
  Locations with a strong electromagnetic field
  This product is provided with ventilation openings in order to prevent overheating.

Ensure that the ventilation openings remain unobstructed by covers or materials. Otherwise, the
internal temperature of the product rises, causing malfunctions.

Intake

Exhaust

Intake

Do not place highly combustible objects such as paper near the product.

«
...
19
20
21
22
23
...
»

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды