manualshive.com logo in svg

A&D RA3100 Omniace, Простое руководство пользователя

Поделиться
Скачать
A&D RA3100 Omniace Скачать руководство пользователя страница 49

 

6.Measuring Input Signals - 6.3.Starting and Ending Recording 

1WMPD4004445 

49 

 
(1)  Mode:   

Selects the optimal mode from the nine recording modes. 

(2)  Data name:   

Specifies the name of the recorded data.   
When [Automatic numbering] is enabled, numbers are automatically appended 
to the name. 

(3)  Recording time:   

Ends recording after recording for the specified time after recording starts. 

(4)  Start time: 

Starts recording at the specified time after starting measurement with 
the    START    key. 

(5)  Interval time:   

Performs recording at the specified interval. Recording ends when recording 
has been performed the number of times specified in [Number of Recording 
times]. 

(6)  Recording device:   

Enables/disables recording to the recording device (Printer, SSD, or Memory). 
The devices can be set independently. 

(7)  Printer :   

Enables/disables printer recording.   
When enabled, the P-P data is recorded to the SSD with sampling of printer 
recording. 

 

Real-time printing:   

When printer recording is enabled, real-time printing to the printer can be 
enabled/disabled.   
When enabled, the waveform of the specified sheet is printed from the printer 
while saving the data of the printer recording.   
When disabled, printing to the printer is not performed. 

(8)  SSD:   

Enables/disables SSD recording. 

(9)  Memory:   

Enables/disables memory recording. 

 

Points:   

Specifies the sampling count (the data count per channel) to record for each 
memory recording. 

 

Recording blocks:   

Specifies the number of blocks to record for memory recording. 

 

Endless mode:   

When the endless mode is enabled, the blocks start to be overwritten from the 
first block when the record blocks are full. 

 

Pre-trigger:   

Sets the pre-trigger in the memory block. 

(10) Thumbnail:   

Specifies the channels to display thumbnails for and the compression rate. 

 

 

Содержание RA3100 Omniace













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды