3M Multimedia Projector MP8610 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 49

background image

3M



Multimedia Projector MP8610

Troubleshooting



3M 1999

3-9

3-3-8.

Humming Noise. Slowly Passing Horizontal Bars

Probable causes are:

•

Signal sources are connected to different power sources.

•

VCR connected to aerial system and to projector.

•

Bad signal.

Possible solutions are:

•

Locate the source of disturbance. Disconnect the sources one after another from the projector.

Connect all

sources to a common power source.

•

Remove antenna connection from VCR. If the disturbance disappears, use a bypass filter (isolating
transformer) to connect the antenna to the VCR.

•

Try different input source.

3-3-9.

No Power. Power Shuts Off During Presentation

Probable causes are:

•

Power switch OFF.

•

Projector overheated.

Possible solutions are:

•

Turn on Power switch to projector.

•

Remove any objects blocking ventilation and allow projector to cool down. Power will return and projector
will be in Standby mode.MP8610 Message Table

«
...
34
35
36
37
38
...
»

Содержание Multimedia Projector MP8610


















































Отзывы:

Нет отзывов

Похожие инструкции для Multimedia Projector MP8610

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 58

Бренд: NEC Страницы: 1

Бренд: Optoma Страницы: 1

Бренд: Emos Страницы: 4

ACCU DECOLITE IP

Бренд: JB Systems Страницы: 16

SCREEN Standard

Бренд: FART PRODUKT Страницы: 5

Бренд: ViewSonic Страницы: 57

Бренд: Magnavox Страницы: 54

Бренд: M-system Страницы: 5

Бренд: Belkin Страницы: 1

PROJECTIONLINK BNDL-001

Бренд: Proxima Страницы: 64

MEDALLION WS-55615

Бренд: Mitsubishi Страницы: 81

Бренд: Ask Proxima Страницы: 45

Бренд: Sanyo Страницы: 1

Бренд: Sanyo Страницы: 2

Бренд: Sanyo Страницы: 40

Бренд: Sanyo Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды